Correction to Disassembly and Assembly , "Piston Pump (Steering) - Disassemble" {4306, 5070}
`
2003/03/31
[SEPD0677]
2003/03/31
Correction to Disassembly and Assembly , "Gear Pump (Axle Oil Cooler) - Remove and Install" {5073}
2003/03/31
Correction to Disassembly and Assembly , "Bucket" {6101}
STEERING SYSTEM
PUMP GP
2003/03/31
Correction to Disassembly and Assembly , "Piston Pump (Steering) - Disassemble" {4306, 5070}
- Wheel Loader:
- 992G (S/N: 7HR1-UP; ADZ1-UP)
- Wheel Tractor:
- 854G (S/N: AMP1-UP; 1JW1-UP)
A portion of the existing information is incorrect. Replace Steps 27 through 29 in the Disassembly and Assembly, "Piston Pump (Steering) - Disassemble" with the following information.
- Remove four screws (57) from pump housing (37) .
Show/hide table
 | |
| Illustration 1 | g00989387 |
- Use two forcing screws (A) to remove seal carrier (58) from pump housing (37) and shaft (33) .
Show/hide table
 | |
| Illustration 2 | g00989379 |
- Remove O-ring seals (60) from the seal carrier. Remove shaft seals (59) .
Show/hide table
 | |
| Illustration 3 | g00989381 |
Information System:
651E and 657E Wheel Tractor-Scrapers Power train
Power Train Troubleshooting
C7 Engines for Caterpillar Built Machines
Crankshaft Front Seal - Install
3054E Industrial Engine
Housing (Front) - Install
C7 Engines for Caterpillar Built Machines
Crankshaft Front Seal - Remove
AD30 Underground Articulated Truck
Oscillating Hitch - Lubricate
G3500B Engines
Start/Stop Control
2003/03/31
Correction to Disassembly and Assembly , "Gear Pump (Axle Oil Cooler) - Remove and Install" {5073}
2003/03/31
Correction to Disassembly and Assembly , "Axle Shaft Assemblies" {3259}
Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070}
Installation of 9SU (S/N: 9RP; T9J) and 9U (S/N: 9MP; T9H) Bulldozer with a Single Tilt Cylinder {5104, 6050}
AD30 Underground Articulated Truck
Drive Shaft Universal Joints, Splines and Bearings - Inspect/Lubricate
C7 Engines for Caterpillar Built Machines
Unit Injector Sleeve - Install
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Safety Messages
D6N Track-Type Tractor Machine Systems
Bulldozer Control Valve - Disassemble
D6N Track-Type Tractor Machine Systems
Bulldozer Control Valve - Assemble
AD30 Underground Articulated Truck
Steering Cylinder Bearings - Lubricate
AD30 Underground Articulated Truck
Screen (Torque Converter) - Clean
AD30 Underground Articulated Truck
Engine Air Filter Secondary Element - Replace
TH350B, TH355B, TH360B and TH460B Telehandlers
Braking System - Test
2003/03/31
Correction to Disassembly and Assembly , "Bucket" {6101}
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Cooling System Coolant Sample (Level 1) - Obtain
963C Track-Type Loader
Track - Check/Adjust
C15 and C18 Generator Set Engines
Crankshaft Main Bearings - Install
C15 On-Highway Engine
Crankshaft - Remove