The AccuGrade Blade Angle Sensor Bracket Has Been Relocated and Has a New Designed Cover On Certain D6K2 and D6N Track-Type Tractors {6052, 6060, 6701}
`
2014/12/19
[SEPD1906]
2014/12/19
Improved Diagnostic Process is Available for the High Pressure Fuel System on C6.6 and C4.4 Machine Engines {1251, 1290}
2014/12/19
An Improved Main Hydraulic Pump Position Sensor Group is Now Used on Certain Excavators and Wheel Loaders {5070}
WORK TOOLS
BLADE GP
2014/12/19
The AccuGrade Blade Angle Sensor Bracket Has Been Relocated and Has a New Designed Cover On Certain D6K2 and D6N Track-Type Tractors {6052, 6060, 6701}
- Track-Type Tractor:
- D6K2 (S/N: MXK1-UP; WMR1-UP; RST1-UP)
- D6N (S/N: PBA1-UP; PER1-UP; GHS1-UP; MLW1-UP)
Description of Change: The blade angle sensor can now be mounted on a bracket that is protected by a new designed cover. The bracket location offers a better protection to the connector coil and enhances the durability of the system.
Adaptable To: This improvement is effective with the following machines:
- D6K2 (S/N: MXK189-UP; RST1283-UP; WMR773-UP)
- D6N (S/N: GHS1827-UP; PBA2471-UP; MLW1126-UP; PER901-UP)
- D6K2 (S/N: MXK1-188; RST1-1282; WMR1-772)
- D6N (S/N: GHS1-1826; PBA1-2470; MLW1-1125; PER1-900)
Show/hide table
| Required Parts | |||
| Item | Qty | Part Number | Description |
| 1 | 1 | 450-3991 | Plate As |
| 2 | 1 | 450-3992 | Cover |
| 3 | 2 | 8T-4189 | Bolt |
| 4 | 2 | 8T-4224 | Hard Washer |
Show/hide table
 | |
| Illustration 1 | g03718906 |
Show/hide table
| Dimensions | ||||
| Sales Model | Blade Group | Dimension (A) | Dimension (B) | Weld (C) to (D) |
| D6N LGP (S/N: PBA; GHS) | 359-3349 | 70 ± 3 mm (2.8 ± 0.12 inch) |
940 ± 2 mm (37 ± 0.079 inch) |
4 mm (0.16 inch) |
| D6N XL (S/N: PER; MLW) | 358-2210 358-2259 |
20 ± 3 mm (0.79 ± 0.12 inch) |
796.9 ± 2 mm (31.37 ± 0.079 inch) |
4 mm (0.16 inch) |
| D6N LGP (S/N: PBA; GHS) | 359-3410 | 20 ± 3 mm (0.79 ± 0.12 inch) |
796.9 ± 2 mm (31.37 ± 0.079 inch) |
4 mm (0.16 inch) |
| D6K2 LGP (S/N: RST; MXK) | 348-6280 371-0779 |
20 ± 3 mm (0.79 ± 0.12 inch) |
784 ± 2 mm (30.87 ± 0.079 inch) |
4 mm (0.16 inch) |
| D6K2 XL (S/N: WMR; MXK) | 348-6300 371-0749 |
20 ± 3 mm (0.79 ± 0.12 inch) |
784 ± 2 mm (30.87 ± 0.079 inch) |
4 mm (0.16 inch) |
- Weld plate assembly (1) to the back of the blade using Illustration 1 and the dimensions in Table 2 as a reference.
- Install cover (2) onto plate assembly (1) using two bolts (3) and two washers (4) .
Show/hide table
 | |
| Illustration 2 | g03720460 |
Information System:
950 GC Wheel Loader Power Train
Fixed Axle (Front) - Remove and Install
525D, 535D, 545D, 555D Wheel Skidder
Engine Operation
C3.4B Engines
DEF Line Heater - Test
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems
Transmission Lubrication
525D, 535D, 545D, 555D Wheel Skidder
Secondary Steering - (If Equipped)
D6N Track-Type Tractor
Brake System
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Engine Supplement
Engine, Torque Converter, Transmission and Output Transfer Gears - Install
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems
Output Transfer Gears
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems
Differential Backlash and Bearings - Adjust
966K Wheel Loader Electrohydraulic System
Relief Valve (Load Sensing Signal) - Test and Adjust
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems
Differential Pinion Preload - Adjust
C280 Marine Engines
Exhaust Temperature Is Low
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems
Transfer Gear Bearing Preload - Adjust
3516B Generator Set Engines with Dynamic Gas Blending
Camshaft Timing
950 GC Wheel Loader Power Train
Trunnion Support (Oscillating Axle, Rear) - Remove and Install
D7E Track-Type Tractor
Engine Oil and Filter - Change
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems
Steering Control Valve
3516B Generator Set Engines with Dynamic Gas Blending
Intake Manifold Air Temperature Is High
3500E EPA Tier 4 Final and IMO-II/III Switchable Marine Engines
Engine Control Switch - Test
C280 Marine Engines
Secondary ECM Assumes Control
Fast Fill Hose Inspection On Certain D8TTrack-Type Tractors Equipped With a Fast Fuel Attachment{1273, 1710}
D7E Track-Type Tractor Systems
Electronic Control (Power Train System)
2014/10/16
New Ejector Cylinder Group is Now Used on Certain 631G and 637G Wheel Tractor-Scrapers {5305}
D4, D6K2 and D6K Track-Type Tractor Systems
Electronic Control (Hydraulic System)