New Sensors Are Now Available For the Implement Control Lever On Certain Track-Type Tractors {5737}
`
2009/06/15
[SEPD0996]
2009/06/15
New Software Is Now Used For Elevated Idle {1901, 1902, 1920}
2009/06/15
The Engine Enclosure May Need to Be Updated {7267, 7276}
ELECTRICAL AND STARTING SYSTEM
SENSOR GP
2009/06/15
New Sensors Are Now Available For the Implement Control Lever On Certain Track-Type Tractors {5737}
- Track-Type Tractor:
- D8T (S/N: J8B1-UP; KPZ1-UP)
- D9T (S/N: RJS1-UP)
- D10R (S/N: AKT1-UP)
- D10T (S/N: RJG1-UP)
- D11R (S/N: AAF1-UP; 9XR1-UP; 7PZ1-UP)
- D11T (S/N: GEB1-UP)
New sensors are now available for the 226-7420 Ripper Control. The 266-1474 Position Sensor Gp that controls the shank in and the shank out replaces the 219-2390 Position Sensor Gp. The 266-1475 Position Sensor Gp that controls the raising and the lowering of the ripper replaces the 219-2391 Position Sensor Gp. The new sensors will improve the reliability of the implement control lever.
The new sensors are adaptable to the machines that are listed above.
Required Parts
Show/hide table
| Required Parts | |||
| New Part Number | Description | Former Part Number | Quantity |
| 266-1474 | Position Sensor Gp | 219-2390 | 1 |
| 266-1475 | Position Sensor Gp | 219-2391 | 1 |
Rework Procedure
- Remove the plate and the control group from the console.
Show/hide table
 | |
| Illustration 1 | g01931468 |
- Disconnect the electrical connections.
- Unbolt the plate from the control group.
- Replace the 219-2390 Position Sensor Gp with a new 266-1474 Position Sensor Gp. Replace the 219-2391 Position Sensor Gp with a new 266-1475 Position Sensor Gp .
- Mount the control group to the plate.
- Connect the electrical connections.
- Mount the plate and the control group to the console.
Information System:
D7E Track-Type Tractor
Declaration of Conformity
C13 Engines for Caterpillar Built Machines
Fuel System Pressure - Test
C13 Engines for Caterpillar Built Machines
Fuel System - Prime
973D Track-Type Loader
Monitoring System
2009/06/15
New Software Is Now Used For Elevated Idle {1901, 1902, 1920}
CUSTOM SERVICE INFORMATION for the 980H UNDERGROUND MINE AR {1050, 1051, 4250, 4267, 4300, 4307, 4330, 5050, 5109, 5112, 5134, 7000}
C9.3 Engines for Caterpillar Built Machines
Fuel Manifold - Remove and Install - Return
3500B Engines
Air Shutoff
973D Track-Type Loader Hydraulic System
General Information
D7E Track-Type Tractor
Lifting and Tying Down the Machine
988G Wheel Loader Power Train
Torque Converter (Lockup) - Assemble - Type 2
D6T Track-Type Tractor Hydraulic System
Piston Pump (Steering)
2009/09/07
Protective Covers For the Joint On the Equalizer Bar Are Now Used {7206}
973D Track-Type Loader Hydraulic System
Tilt Circuit
2009/06/15
The Engine Enclosure May Need to Be Updated {7267, 7276}
973D Track-Type Loader Hydraulic System
Bucket Control
973D Track-Type Loader Hydraulic System
Multipurpose Bucket Circuit
973D Track-Type Loader Hydraulic System
Signal Resolver Network
973D Track-Type Loader Hydraulic System
Ripper Circuit
D5R Track-Type Tractor
Implement Cycle Time Is Slow
C9.3 Tier 4 Final Engines
General Information
973D Track-Type Loader Hydraulic System
Lift Circuit
C9.3 Tier 4 Final Engines
Basic Engine
Repair and Reinforcement of the Rear Frame for the 988G and 988H Machines in Special Applications{7051}