3044C Industrial Engine and Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install Caterpillar


Water Temperature Regulator Housing - Remove and Install
`
3044C Industrial Engine and Engines for Caterpillar Built Machines [RENR7582]
COOLING SYSTEM
LINES GP-WATER
3044C Industrial Engine and Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "AVSpare Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on AVSpare products.

Dispose of all fluids according to local regulations and mandates.


  1. Drain the cooling system. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".



    Illustration 1g01035909

  1. Remove bolts (2). Remove elbow assembly (1) and gasket (3) .



    Illustration 2g01035910

  1. Remove water temperature regulator (4). Note the orientation of the water temperature regulator for installation purposes.



    Illustration 3g01035912

  1. Loosen clamp (8) and disconnect hose (9). Remove bolts (7). Remove water temperature regulator housing (5) and gasket (6) .

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.





    Illustration 4g01035912

  1. Install gasket (6) and position water temperature regulator housing (5). Install bolts (7). Connect hose (9) and tighten clamp (8) .



    Illustration 5g01035910

  1. Note the orientation of water temperature regulator (4). Install water temperature regulator (4) .



    Illustration 6g01035909

  1. Install gasket (3) and elbow assembly (1). Install bolts (2) .

  1. Fill the cooling system. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".

Information System:

613C Series II Wheel Tractor Power Train Torque Converter - Disassemble
3044C Industrial Engine and Engines for Caterpillar Built Machines Water Pump - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
613C Series II Wheel Tractor Power Train Torque Converter - Install
2003/05/19 Correction to Testing and Adjusting , "Ride Control Accumulator Recharging Procedure" {5077}
2003/05/12 Correction to Testing and Adjusting , "Transmission Pressures - Test and Adjust" {3081}
613C Series II Wheel Tractor Power Train Torque Converter - Remove
980G Series II Wheel Loader Power Train Transmission Pressures - Test and Adjust
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install
613C Series II Wheel Tractor Power Train Transmission and Transfer Gears - Install
TH220B, TH330B and TH340B Telehandlers Transmission and Hydraulic System Oil Level - Check
953C Track-Type Loader Hydraulic System Bucket Control Group
613C Series II Wheel Tractor Power Train Torque Converter - Assemble
2003/06/02 New Guard Assembly for the Tilt Position Sensor Is Used {5736}
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Diagnostic Code List
854G Wheel Tractor and 992G Wheel Loader Power Train Axle Shaft - Remove and Install
980G Series II Wheel Loader Cooling System Coolant Sample (Level 1) - Obtain
3044C Industrial Engine and Engines for Caterpillar Built Machines Fuel Injection Lines - Remove and Install - Turbocharged Engines
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Oil Cooler - Remove
854G Wheel Tractor and 992G Wheel Loader Power Train Transmission Hydraulic Control Valve - Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Oil Cooler - Install
AD30 Underground Articulated Truck Machine Electrical System Brake Oil Temperature
966G II and 972G II Wheel Loaders Monitoring System
854G Wheel Tractor and 992G Wheel Loader Power Train Transmission Hydraulic Control Valve - Remove