Water Pump - Remove and Install
`
3044C Industrial Engine and Engines for Caterpillar Built Machines
[RENR7582]
3044C Industrial Engine and Engines for Caterpillar Built Machines
Engine Oil Relief Valve - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines
Water Temperature Regulator Housing - Remove and Install
COOLING SYSTEM
PUMP GP-WATER
3044C Industrial Engine and Engines for Caterpillar Built Machines
Water Pump - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Removal Procedure
Show/hide table
 |
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool. |
 |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "AVSpare Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on AVSpare products. Dispose of all fluids according to local regulations and mandates. |
- Drain the cooling system. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
- Loosen clamp (2) and disconnect hose (1). Remove bolts (3) and pulley (4) .
Show/hide table
 | |
| Illustration 1 | g01035994 |
- Remove bolts (7). Remove water pump (6) and gasket (5) .
Show/hide table
 | |
| Illustration 2 | g01036000 |
Installation Procedure
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install gasket (5) and position water pump (6). Install bolts (7) .
Show/hide table
| | |
| Illustration 3 | g01036000 |
- Connect hose (1) and tighten clamp (2). Position pulley (4) and install bolts (3) .
Show/hide table
| | |
| Illustration 4 | g01035994 |
- Fill the cooling system. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
Information System:
3044C Industrial Engine and Engines for Caterpillar Built Machines
Engine Oil Relief Valve - Remove and Install
613C Series II Wheel Tractor Power Train
Torque Converter - Install
2003/05/19
Correction to Testing and Adjusting , "Ride Control Accumulator Recharging Procedure" {5077}
2003/05/12
Correction to Testing and Adjusting , "Transmission Pressures - Test and Adjust" {3081}
613C Series II Wheel Tractor Power Train
Torque Converter - Remove
980G Series II Wheel Loader Power Train
Transmission Pressures - Test and Adjust
3044C Industrial Engine and Engines for Caterpillar Built Machines
Engine Oil Filter Base - Remove and Install
613C Series II Wheel Tractor Power Train
Transmission and Transfer Gears - Install
TH220B, TH330B and TH340B Telehandlers
Transmission and Hydraulic System Oil Level - Check
953C Track-Type Loader Hydraulic System
Bucket Control Group
3044C Industrial Engine and Engines for Caterpillar Built Machines
Exhaust Manifold - Remove and Install
963C Track-Type Loader
Maintenance Interval Schedule
613C Series II Wheel Tractor Power Train
Torque Converter - Disassemble
3044C Industrial Engine and Engines for Caterpillar Built Machines
Water Temperature Regulator Housing - Remove and Install
613C Series II Wheel Tractor Power Train
Torque Converter - Assemble
2003/06/02
New Guard Assembly for the Tilt Position Sensor Is Used {5736}
D3G, D4G and D5G Track-Type Tractors Electrohydraulic
Diagnostic Code List
854G Wheel Tractor and 992G Wheel Loader Power Train
Axle Shaft - Remove and Install
980G Series II Wheel Loader
Cooling System Coolant Sample (Level 1) - Obtain
3044C Industrial Engine and Engines for Caterpillar Built Machines
Fuel Injection Lines - Remove and Install - Turbocharged Engines
3044C Industrial Engine and Engines for Caterpillar Built Machines
Engine Oil Cooler - Remove
854G Wheel Tractor and 992G Wheel Loader Power Train
Transmission Hydraulic Control Valve - Install
3044C Industrial Engine and Engines for Caterpillar Built Machines
Engine Oil Cooler - Install
AD30 Underground Articulated Truck Machine Electrical System
Brake Oil Temperature