Engine Oil Filter Base - Remove and Install
`
3044C Industrial Engine and Engines for Caterpillar Built Machines
[RENR7582]
3044C Industrial Engine and Engines for Caterpillar Built Machines
Exhaust Manifold - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines
Engine Oil Relief Valve - Remove and Install
LUBRICATION SYSTEM
FILTER GP-ENGINE OIL
3044C Industrial Engine and Engines for Caterpillar Built Machines
Engine Oil Filter Base - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 185-3630     | Strap Wrench As     | 1     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "AVSpare Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on AVSpare products. Dispose of all fluids according to local regulations and mandates. |
- Use Tooling (A) to remove engine oil filter (1). Remove bolts (3) and (4). Remove engine oil filter base (2) .
Show/hide table
Illustration 1 | g01035650 |
- Remove O-ring seal (5) from bolt (3). Remove O-ring seal (6) from engine oil filter base (2) .
Show/hide table
Illustration 2 | g01035651 |
Installation Procedure
- Install O-ring seal (6) on engine oil filter base (2). Install O-ring seal (5) on bolt (3) .
Show/hide table
Illustration 3 | g01035651 |
- Position engine oil filter base (2). Install bolts (3) and (4). Install engine oil filter (1) .
Show/hide table
Illustration 4 | g01035650 |
Information System:
613C Series II Wheel Tractor Power Train
Transmission and Transfer Gears - Install
TH220B, TH330B and TH340B Telehandlers
Transmission and Hydraulic System Oil Level - Check
953C Track-Type Loader Hydraulic System
Bucket Control Group
3044C Industrial Engine and Engines for Caterpillar Built Machines
Exhaust Manifold - Remove and Install
963C Track-Type Loader
Maintenance Interval Schedule
613C Series II Wheel Tractor Power Train
Transmission and Transfer Gears - Remove
3044C Industrial Engine and Engines for Caterpillar Built Machines
Fuel Injection Lines - Remove and Install - Naturally Aspirated Engines
953C Track-Type Loader Hydraulic System
Pilot Valve
615C Series II Wheel Tractor-Scraper Wheel Tractor Power Train
Leading Arm - Install
963C Track-Type Loader Power Train
Hydraulic Drive Pump - Assemble
963C Track-Type Loader Power Train
Hydraulic Drive Pump - Disassemble
615C Series II Wheel Tractor-Scraper Wheel Tractor Power Train
Leading Arm - Remove
980G Series II Wheel Loader Power Train
Transmission Pressures - Test and Adjust
613C Series II Wheel Tractor Power Train
Torque Converter - Remove
2003/05/12
Correction to Testing and Adjusting , "Transmission Pressures - Test and Adjust" {3081}
2003/05/19
Correction to Testing and Adjusting , "Ride Control Accumulator Recharging Procedure" {5077}
613C Series II Wheel Tractor Power Train
Torque Converter - Install
3044C Industrial Engine and Engines for Caterpillar Built Machines
Engine Oil Relief Valve - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines
Water Pump - Remove and Install
613C Series II Wheel Tractor Power Train
Torque Converter - Disassemble
3044C Industrial Engine and Engines for Caterpillar Built Machines
Water Temperature Regulator Housing - Remove and Install
613C Series II Wheel Tractor Power Train
Torque Converter - Assemble
2003/06/02
New Guard Assembly for the Tilt Position Sensor Is Used {5736}
D3G, D4G and D5G Track-Type Tractors Electrohydraulic
Diagnostic Code List