3054E Industrial Engine Fuel Injection Pump - Install Caterpillar


Fuel Injection Pump - Install
`
1.1. Installation Procedure

Installation Procedure

Table 1
Required Tools 
Tool  Part Number  Part Name  Qty 
A  9U-6198  Crankshaft Turning Tool 
B  230-6284  Timing Pin (Camshaft) 
C  230-6283  Timing Pin (Crankshaft) 
D  150-3992  Timing Pin (Fuel Injection Pump) 
E  157-3719  Ratchet Wrench 


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


  1. Ensure that the No. 1 cylinder is at top dead center on the compression stroke. Refer to the Testing and Adjusting Manual, "Finding Top Center Position for No. 1 Piston".

  2. Ensure that all the mating surfaces are clean and free from fluid.


    Illustration 1g00994376

  3. Install a O-ring seal (8) on the fuel injection pump. Position the fuel injection pump on the front housing. Install new sealing washers onto the setscrews and install the three setscrews (11). Tighten the setscrews to a torque of 22 N·m (16.2 lb ft).

  4. If necessary, install the setscrew and bracket (12) on the cylinder block. Tighten the setscrew by hand.

  5. Install the nut and setscrew (13). Tighten the setscrew by hand.

    Note: The fasteners (12) and (13) must be secured after the front cover is installed.

  6. Connect the tube assembly (9) to the fuel injection pump. Connect the tube assembly (10) to the fuel injection pump.

  7. Connect the harness assembly (7) to the fuel injection pump. Push the locking mechanism in order to secure the harness assembly.

  8. Use the Tooling (A) to ensure that the No. 1 cylinder is at the top center compression stroke. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".


    Illustration 2g00994453

  9. Insert the Tooling (D) through the slot in the hub and into the timing hole of the Fuel Injection Pump. If the Tooling (D) can be fully inserted, the fuel injection timing is correct. There should be no resistance when the Tooling (D) is inserted.

    Note: The Tooling (B), the Tooling (C), and the Tooling (D) must be installed before the fuel injection pump gear (2) is installed on the hub of the fuel injection pump.

    Note: Some Bosch VP30 fuel injection pumps do not have a locking screw. For more information on timing the fuel injection pump, refer to Systems Operation, Testing and Adjusting, "Fuel Injection Timing - Check".

    Note: Do not remove the hub nut (1) from the shaft of the fuel injection pump. The hub of the fuel injection pump is installed in the correct position from the factory in order to ensure proper timing. If the hub nut (1) is removed and the hub is removed, the hub will need to be accurately installed on the shaft of the fuel injection pump by the use of special equipment. Refer to your AVSpare Dealer for more information.



    Illustration 3g00994481
    Fuel Injection Pump Gear

  10. Position the slot in the fuel injection pump gear (2) over the Tooling (D). Install the four setscrews (3) and washers. Do not tighten the setscrews at this time.

  11. Rotate the fuel injection pump gear counterclockwise in order to remove the backlash between the idler gear and the fuel injection pump gear. Tighten the four setscrews (3) to a torque of 22 N·m (16.2 lb ft).

  12. Remove the Tooling (D) from the fuel injection pump. Remove the Tooling (B) from the camshaft gear. Remove the Tooling (C) from the crankshaft web.


    Illustration 4g00995133

  13. Loosen the setscrew (4). Install the spacer (5) in order to prevent the setscrew (4) from tightening against the shaft of the fuel injection pump (6). Tighten the setscrew (4) to a torque of 12 N·m (9 lb ft).

End By:

  1. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove and Install".

  2. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install".

  3. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley - Remove and Install".

  4. Refer to illustration 1. Tighten the setscrew (12) to a torque of 44 N·m (32.5 lb ft). Tighten the setscrew and the nut (13) to a torque of 22 N·m (16.2 lb ft).

  5. Install the air compressor, if equipped. Refer to Disassembly and Assembly, "Air Compressor - Remove and Install".

Information System:

AD30 Underground Articulated Truck Machine Electrical System Main Power Relay
AD30 Underground Articulated Truck Machine Electrical System Circuit Breaker
2003/05/05 New Engine Software Improves the Engine Compression Brake and Throttle Lock Operation {1920, 7620}
3406E and 3456 Generator Set Engines E173 High Exhaust Temperature Warning
Bench Test Procedure for a D9R Track-Type Tractor Transmission with Differential Steering {3030, 3073}
3500B Series II Marine Engines E100 Low Engine Oil Pressure Warning
3500B Series II Marine Engines E040 Low Engine Oil Pressure Shutdown
AD30 Underground Articulated Truck Braking System System Pressure - Release
2003/05/26 A Rework Procedure is Now Available to Improve the Mounting of the Ripper Valve {5351, 6310}
3516B Generator Set Engines with Dynamic Gas Blending Factory Passwords
963C Track-Type Loader Power Train Pressure Override Valve - Adjust
3046 Engine for Caterpillar Built Machines Glow Plugs - Test
IT62G Series II Integrated Toolcarrier and 950G Series II and 962G Series II Wheel Loaders Rated Load
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Plate Locations and Film Locations
IT62G Series II Integrated Toolcarrier and 950G Series II and 962G Series II Wheel Loaders Engine Starting
IT62G Series II Integrated Toolcarrier and 950G Series II and 962G Series II Wheel Loaders Lift Kickout
3500 Industrial Engines Accumulator Pressure - Test
IT62G Series II Integrated Toolcarrier and 950G Series II and 962G Series II Wheel Loaders Cooling System Coolant Sample (Level 1) - Obtain
2003/05/12 New Front Crankshaft Seals and New Rear Crankshaft Seals are Now in Production {1160, 1161}
D5N Track-Type Tractor Monitoring System
IT62G Series II Integrated Toolcarrier and 950G Series II and 962G Series II Wheel Loaders Differential and Final Drive Oil Sample - Obtain
AD30 Underground Articulated Truck Machine Electrical System Head Light/Park Light
2003/05/05 A New Parking Brake Switch is Available {1408, 1435}
AD30 Underground Articulated Truck Machine Electrical System Block Light/Rear Cab Flood Light