D6N Track-Type Tractor Power Train Final Drive, Steering Differential, and Brake (Left Side) - Install Caterpillar


Final Drive, Steering Differential, and Brake (Left Side) - Install
`
1.1. Installation Procedure

Installation Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
8T-3207  Lifting Bracket 
138-7575  Link Bracket 
8S-9906  Ratchet Puller 

Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.



    Illustration 1g00992351

  1. Attach Tooling (D) to Tooling (C) and Tooling (B).


    Illustration 2g00992352

  2. Rotating the brake housing allows pinion (7) to point forward. Position the brake housing to the original location. The weight of the final drive assembly is approximately 680 kg (1500 lb).

  3. Install the final drive in the case. Rotate the brake housing until all the bolt holes line up.


    Illustration 3g00992350

  4. Install bolts (3) and washers.


    Illustration 4g00865077

  5. Install bolts (6) in the top of the sprocket.


    Illustration 5g00992349

  6. Remove Tooling (C). Install remaining bolts (3).

  7. Install bolt (4). Install two bolt (5).

  8. Remove Tooling (B). Install bolts (6) in the top of the sprocket segment.


    Illustration 6g00992383

  9. Install housing (2) and bolts (1).

End By:

  1. Install the axles. Refer to Disassembly and Assembly, "Axle - Remove and Install".

  2. Install the steering motor. Refer to Disassembly and Assembly, "Steering Motor - Install".

  3. Connect the track. Refer to Disassembly and Assembly, "Track - Connect".

Information System:

D6N Track-Type Tractor Power Train Final Drive, Steering Differential, and Brake (Left Side) - Remove
D6N Track-Type Tractor Power Train Steering Differential and Brake - Disassemble
TH560B Telehandler Lifting Capacities
AD30 Underground Articulated Truck Service Inspection
953C Track-Type Loader Engine Oil Sample - Obtain
953C Track-Type Loader Cooling System Water Temperature Regulator - Clean/Replace
953C Track-Type Loader Cooling System Extended Life Coolant - Change
Rotating Group Adjustment Instructions for Bosch Rexroth Hydraulic Pumps and Motors {3203, 4351, 5058, 5070}
CAES Installation For Wheel Tractor Scraper{7604}
CAES Installation For Wheel Loader{7604}
953C Track-Type Loader Engine Starting with Jump Start Cables
D6N Track-Type Tractor Power Train Axle - Remove and Install
3126B Engine for Caterpillar Built Machines Sensors and Electrical Connectors
D6N Track-Type Tractor Power Train Priority Valve - Disassemble
D6N Track-Type Tractor Power Train Priority Valve - Assemble
Repair of Cracks in the Rear Track Roller Frame{4151}
C-9 Engine for the 973C Track-Type Loader Engine Will Not Crank
AD30 Underground Articulated Truck Tailgate Retaining Pin
2003/07/14 Correction to Systems Operation , "Selector and Pressure Control Valve" {3073, 3157}
AD45B Underground Articulated Truck Oscillating Hitch - Adjust
AD30 Underground Articulated Truck Steering System Oil Filter - Replace
3126B Engine for Caterpillar Built Machines System Configuration Parameters
924G and 924GZ Wheel Loaders Machine Systems Main Control Valve - Disassemble
924G and 924GZ Wheel Loaders Machine Systems Main Control Valve - Assemble