Camshaft Bearings - Remove and Install
`
C7 Engines for Caterpillar Built Machines
[RENR9218]
C7 Engines for Caterpillar Built Machines
Camshaft Idler Gear - Remove and Install
C7 Engines for Caterpillar Built Machines
Fuel Transfer Pump - Remove
BASIC ENGINE
CAMSHAFT GP
C7 Engines for Caterpillar Built Machines
Camshaft Gear - Remove and Install
C7 Engines for Caterpillar Built Machines
Camshaft Bearings - Remove and Install
C7 Engines for Caterpillar Built Machines
Camshaft - Remove
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 8S-2241 | Camshaft Bearing Tool Group | 1 |
Start By:
- Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Note the oil hole orientation in each camshaft bearing prior to removal for assembly purposes.
- Use Tooling (A) to remove camshaft bearing (1) from the front of the cylinder block. Remove the remaining camshaft bearings (2) from the cylinder block.
Show/hide table
| |
| Illustration 1 | g00989974 |
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 8S-2241 | Camshaft Bearing Tool Group | 1 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| |
| Illustration 2 | g00990062 |
- Use Tooling (A) to install all of the camshaft bearings (2) except for the front camshaft bearing. Locate the oil hole in each bearing so that oil hole (3) is located at the top of the bore. Refer to Specifications for more information.
Show/hide table
Illustration 3 g00989938 - Use Tooling (A) to install front camshaft bearing (1). Align oil hole (5) in the front camshaft bearing with the oil hole in the cylinder block. Locate joint (4) in the front camshaft bearing in the proper position. Refer to Specifications for more information.
End By:
- Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Information System:
Installation Instructions for the 2Q-8564 Ride Control Gp (KIT){5004, 5004}
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Differential and Final Drive Oil Sample - Obtain
966G Series II Wheel Loader and 972G Series II Wheel Loader Hydraulic System
Tilt Cylinder - High Lift
C7 Engines for Caterpillar Built Machines
Camshaft Idler Gear - Remove and Install
C15 and C18 Generator Set Engines
Pistons and Connecting Rods - Install
C15 and C18 Generator Set Engines
Connecting Rod Bearings - Remove
C15 On-Highway Engine
Crankshaft - Install
C15 and C18 Generator Set Engines
Pistons and Connecting Rods - Disassemble
C15 On-Highway Engine
Pistons and Connecting Rods - Assemble
C15 On-Highway Engine
Camshaft - Remove
C15 On-Highway Engine
Camshaft - Install
C15 and C18 Generator Set Engines
Connecting Rod Bearings - Install
966G Series II Wheel Loader and 972G Series II Wheel Loader Hydraulic System
Relief Valve
Installation of Product Link{7602}
966G Series II Wheel Loader and 972G Series II Wheel Loader Hydraulic System
Electrohydraulic Control
2003/11/17
Changes to the Mounting Hardware Improve the Service Life of the Rear Frame {7051}
966G Series II Wheel Loader and 972G Series II Wheel Loader Hydraulic System
Pilot Operated Hydraulic Control
AD30 Underground Articulated Truck
Transmission Oil - Change
AD30 Underground Articulated Truck
Transmission Oil Filter - Replace
966G Series II Wheel Loader and 972G Series II Wheel Loader Hydraulic System
Implement System - Electrohydraulic System
966G Series II Wheel Loader and 972G Series II Wheel Loader Hydraulic System
Implement System - Pilot Hydraulics
C18 Industrial Engines
Starting the Engine
3054E Industrial Engine
Boost Pressure Sensor - Remove and Install
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Hydraulic System Oil Sample - Obtain