Camshaft Gear - Remove and Install
`
C7 Engines for Caterpillar Built Machines
[RENR9218]
C7 Engines for Caterpillar Built Machines
Piston Cooling Jets - Remove and Install
C7 Engines for Caterpillar Built Machines
Unit Injector - Remove
BASIC ENGINE
CAMSHAFT GP
C7 Engines for Caterpillar Built Machines
Camshaft Gear - Remove and Install
C7 Engines for Caterpillar Built Machines
Camshaft Bearings - Remove and Install
C7 Engines for Caterpillar Built Machines
Camshaft - Remove
1.1. Removal Procedure
2.1. Installation Procedure
Removal Procedure
Start By:
- Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
- Wrap the camshaft with a protective covering in order to prevent damage to the camshaft.
- Place the camshaft assembly in a suitable press. Press camshaft (2) from camshaft gear (1) .
Show/hide table
 | |
| Illustration 1 | g00987675 |
Show/hide table
| NOTICE |
|---|
Do not allow the camshaft to fall to the floor when pressing it from the drive gear. Also make sure that the camshaft lobes do not catch on the press plates. |
- If necessary, remove key (3) from the camshaft.
Installation Procedure
- Raise the temperature of the camshaft gear from 200° C (392° F) to 250° C (482° F).
Note: Do not use a torch to heat the camshaft gear.
- Align key (3) in the camshaft with the groove (keyway) in the camshaft gear.
Show/hide table
| | |
| Illustration 2 | g00987675 |
- Install camshaft gear (1) on the end of camshaft (2) .
End By: Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Information System:
611 and 615C Series II Wheel Tractor-Scrapers Steering System
Steering System Troubleshooting
611 and 615C Series II Wheel Tractor-Scrapers Steering System
Piston Pump (Secondary Steering)
611 and 615C Series II Wheel Tractor-Scrapers Steering System
General Information
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Pilot Operated Hydraulic Control - Assemble
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Pilot Operated Hydraulic Control - Disassemble
651E and 657E Wheel Tractor-Scrapers Hydraulic System
Relief Valve (Push-Pull) - Test and Adjust
C7 Engines for Caterpillar Built Machines
Piston Cooling Jets - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines
Variable Valve Actuators - Inspect/Adjust
C7 Engines for Caterpillar Built Machines
Rocker Shaft - Disassemble
953C Track-Type Loader
Coolant Sample (Level 2) - Obtain
953C Track-Type Loader
Coolant Sample (Level 1) - Obtain
C7 Engines for Caterpillar Built Machines
Water Temperature Regulator - Remove and Install
980G Series II Wheel Loader Electrohydraulic System
Hydraulic Fan Speed - Test and Adjust
2003/03/24
New Flash Software Allows Calibrations of the Power Train to be Performed by Using the Caterpillar Electronic Technician {0783, 0785, 7620}
2003/04/14
Correction to Testing And Adjusting , "Transmission Testing and Location of The Pressure Taps" {3030, 3073}
2003/04/21
Correction to Testing and Adjusting , "Pressure Tap Locations" {3030}
C7 Engines for Caterpillar Built Machines
Unit Injector - Remove
C7 Engines for Caterpillar Built Machines
Unit Injector - Install
C15 Petroleum Generator Set Engines
Gear Group (Front)
D6N Track-Type Tractor Power Train
Equalizer Bar - Install
D6N Track-Type Tractor Power Train
Equalizer Bar - Remove
D6N Track-Type Tractor Power Train
Front Track Roller Frame - Remove
D6N Track-Type Tractor Power Train
Front Track Roller Frame - Install
D6N Track-Type Tractor Power Train
Pivot Bar-Remove and Install