EPC Parts Catalogs

C7 Engines for Caterpillar Built Machines Rocker Shaft - Disassemble Caterpillar


  1. Home
  2. Disassembly and Assembly
  3. #92931
Rocker Shaft - Disassemble
`
C7 Engines for Caterpillar Built Machines [RENR9218]
C7 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C7 Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
BASIC ENGINE
VALVE MECHANISM GP
C7 Engines for Caterpillar Built Machines Rocker Shaft - Disassemble
C7 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
C7 Engines for Caterpillar Built Machines Valve Mechanism Cover Base - Remove and Install
C7 Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Install
C7 Engines for Caterpillar Built Machines Lifter Group - Remove and Install
1.1. Disassembly Procedure

Disassembly Procedure

Start By:

  1. Remove the rocker shaft. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove".

Show/hide table
NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

    Show/hide table
    Illustration 1g01155738

    Show/hide table
    ------ WARNING! ------

    Personal injury can result from parts and/or covers under spring pressure.

    Spring force will be released when covers are removed.

    Be prepared to hold spring loaded covers as the bolts are loosened.

    Note: Place an identification mark on each of the components of the rocker shaft for installation purposes.

  1. Remove retaining ring (2).

  2. Remove stand (3), inlet rocker arms (4), exhaust rocker arms (5), stands (6), and springs (7) from the rocker shaft.

  3. Remove dowel pin (8) and stand (9) from the rocker shaft.

  4. Remove plug (1).

Information System:

953C Track-Type Loader Coolant Sample (Level 2) - Obtain
953C Track-Type Loader Coolant Sample (Level 1) - Obtain
C7 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
D5N Track-Type Tractor Power Train Track Roller - Install
D5N Track-Type Tractor Power Train Track Roller - Remove
D6N Track-Type Tractor Power Train Recoil Spring - Install
D6N Track-Type Tractor Power Train Recoil Spring - Remove
TH210 and TH215 Telehandlers Lifting Capacities
953C Track-Type Loader Emissions Certification Film
C7 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
953C Track-Type Loader Engine Starting
C7 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Variable Valve Actuators - Inspect/Adjust
C7 Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
651E and 657E Wheel Tractor-Scrapers Hydraulic System Relief Valve (Push-Pull) - Test and Adjust
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Pilot Operated Hydraulic Control - Disassemble
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Pilot Operated Hydraulic Control - Assemble
611 and 615C Series II Wheel Tractor-Scrapers Steering System General Information
611 and 615C Series II Wheel Tractor-Scrapers Steering System Piston Pump (Secondary Steering)
611 and 615C Series II Wheel Tractor-Scrapers Steering System Steering System Troubleshooting
C7 Engines for Caterpillar Built Machines Camshaft Gear - Remove and Install
980G Series II Wheel Loader Electrohydraulic System Hydraulic Fan Speed - Test and Adjust
2003/03/24 New Flash Software Allows Calibrations of the Power Train to be Performed by Using the Caterpillar Electronic Technician {0783, 0785, 7620}
2003/04/14 Correction to Testing And Adjusting , "Transmission Testing and Location of The Pressure Taps" {3030, 3073}