Water Temperature Regulator - Remove and Install
`
C7 Engines for Caterpillar Built Machines
[RENR9218]
C7 Engines for Caterpillar Built Machines
Inlet and Exhaust Valve Seat Inserts - Remove and Install
C7 Engines for Caterpillar Built Machines
Rocker Shaft - Disassemble
COOLING SYSTEM
LINES GP-WATER
C7 Engines for Caterpillar Built Machines
Water Temperature Regulator - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Show/hide table
Illustration 1 g01152619 - Remove bolts (1), pipe (2), and the gasket from water temperature regulator housing (3).
- Remove the water temperature regulators.
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Position the water temperature regulators in water temperature regulator housing (3).
- Install a gasket and pipe (2) on water temperature regulator housing (3).
- Install bolts (1).
- Fill the cooling system. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Show/hide table
| |
| Illustration 2 | g01152619 |
Information System:
D5N Track-Type Tractor Power Train
Track Roller - Install
D5N Track-Type Tractor Power Train
Track Roller - Remove
D6N Track-Type Tractor Power Train
Recoil Spring - Install
D6N Track-Type Tractor Power Train
Recoil Spring - Remove
TH210 and TH215 Telehandlers
Lifting Capacities
953C Track-Type Loader
Emissions Certification Film
C7 Engines for Caterpillar Built Machines
Inlet and Exhaust Valve Seat Inserts - Remove and Install
953C Track-Type Loader
Engine Starting
C7 Engines for Caterpillar Built Machines
Inlet and Exhaust Valve Guides - Remove and Install
980G Series II Wheel Loader Electrohydraulic System
Pump Performance (Pilot and Braking) - Test
C7 Engines for Caterpillar Built Machines
Inlet and Exhaust Valves - Remove and Install
953C Track-Type Loader
Daily Inspection
953C Track-Type Loader
Coolant Sample (Level 1) - Obtain
953C Track-Type Loader
Coolant Sample (Level 2) - Obtain
C7 Engines for Caterpillar Built Machines
Rocker Shaft - Disassemble
C11 and C13 Engines for Caterpillar Built Machines
Variable Valve Actuators - Inspect/Adjust
C7 Engines for Caterpillar Built Machines
Piston Cooling Jets - Remove and Install
651E and 657E Wheel Tractor-Scrapers Hydraulic System
Relief Valve (Push-Pull) - Test and Adjust
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Pilot Operated Hydraulic Control - Disassemble
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Pilot Operated Hydraulic Control - Assemble
611 and 615C Series II Wheel Tractor-Scrapers Steering System
General Information
611 and 615C Series II Wheel Tractor-Scrapers Steering System
Piston Pump (Secondary Steering)
611 and 615C Series II Wheel Tractor-Scrapers Steering System
Steering System Troubleshooting
C7 Engines for Caterpillar Built Machines
Camshaft Gear - Remove and Install