D6N Track-Type Tractor Power Train Recoil Spring - Remove Caterpillar


Recoil Spring - Remove
`
1.1. Removal Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
1P-0820  Hydraulic Puller 
4C-9633 Puller Stud 
8B-7548 Push-Puller Tool Gp 
3H-0465 Push-Puller Plate 
8T-1757 Nut 
9X-8268 Hard Washer 
169-6969 Threaded Rod 
9U-6600 Hand Hydraulic Pump 

Start By:

  1. Remove the front track roller frame. Refer to Disassembly and Assembly, "Front Track Roller Frame.".

  2. Remove the track adjuster. Refer to Disassembly and Assembly, "Track Adjuster - Remove and Install".

------ WARNING! ------

Personal injury can result from being struck by parts propelled by a released spring force.

Make sure to wear all necessary protective equipment.

Follow the recommended procedure and use all recommended tooling to release the spring force.




    Illustration 1g00976493


    Illustration 2g00976494

  1. Position Tooling (A) 280 mm (11.0 inch) away from the roller frame.

  2. Adjust the puller stud so that 25.4 mm (1.00 inch) of travel is allowed. Center the lead bolt onto tube assembly (2).

  3. Apply enough pressure to tube assembly (2) so that tube assembly (2) is off of nut (1). Back off nut (1) by a distance of 12.7 mm (0.50 inch). Slowly release the pressure.

    Note: Do not adjust nut (1) more than 13 mm (0.5 inch) at a time.

  4. Repeat Step 1 through Step 3 until nut (1) is removed.

  5. Remove tube assembly (2).


    Illustration 3g00976495

  6. Attach a suitable lifting device to spring (3). Remove spring (3). The weight of spring (3) is approximately 32 kg (70 lb).

Information System:

TH210 and TH215 Telehandlers Lifting Capacities
953C Track-Type Loader Emissions Certification Film
C7 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
953C Track-Type Loader Engine Starting
C7 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
980G Series II Wheel Loader Electrohydraulic System Pump Performance (Pilot and Braking) - Test
C7 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
953C Track-Type Loader Daily Inspection
TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Power Train Drive and Steering Axle (Front) - Install
TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Power Train Drive and Steering Axle (Front) - Remove
TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Power Train Drive and Steering Axle (Rear) - Install
TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Power Train Drive and Steering Axle (Rear) - Remove
D6N Track-Type Tractor Power Train Recoil Spring - Install
D5N Track-Type Tractor Power Train Track Roller - Remove
D5N Track-Type Tractor Power Train Track Roller - Install
C7 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
953C Track-Type Loader Coolant Sample (Level 1) - Obtain
953C Track-Type Loader Coolant Sample (Level 2) - Obtain
C7 Engines for Caterpillar Built Machines Rocker Shaft - Disassemble
C11 and C13 Engines for Caterpillar Built Machines Variable Valve Actuators - Inspect/Adjust
C7 Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
651E and 657E Wheel Tractor-Scrapers Hydraulic System Relief Valve (Push-Pull) - Test and Adjust
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Pilot Operated Hydraulic Control - Disassemble
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Pilot Operated Hydraulic Control - Assemble