Bulldozer (VPAT) - Remove
`
D6N Track-Type Tractor Machine Systems
[RENR5274]
D6N Track-Type Tractor Machine Systems
Rollover Protective Structure (ROPS) - Remove and Install
D6N Track-Type Tractor Machine Systems
Bulldozer (VPAT) - Install
IMPLEMENTS
BULLDOZER GP
D6N Track-Type Tractor Machine Systems
Bulldozer (VPAT) - Remove
D6N Track-Type Tractor Machine Systems
Bulldozer (VPAT) - Install
1.1. Removal Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 189-0410 | Shackle As | 2 |
| B | 9U-5344 | Puller Stud | 1 |
| 1U-7552 | Hydraulic Cylinder Gp | 1 | |
| 1U-7544 | Hydraulic Hand Pump Gp | 1 | |
| 9X-8399 | Washer | 1 | |
| 9U-5346 | Nut | 1 | |
| C | 1U-9756 | Jack | 1 |
| D | FT-2802 | Puller Plate | 1 |
| 6V-2108 | Sleeve | 1 | |
| 6V-3160 | Double Acting Cylinder | 1 | |
| 9U-6600 | Hand Hydraulic Pump | 1 | |
| 9U-5343 | Puller Stud | 1 | |
| 9U-5345 | Nut | 1 | |
| 6V-8237 | Washer | 1 | |
| E | 5P-5197 | Retaining Ring Pliers As | 1 |
| F | FT-2802 | Puller Plate | 1 |
| 134-8470 | Sleeve | 1 | |
| 6V-3160 | Double Acting Cylinder | 1 | |
| 9U-6600 | Hand Hydraulic Pump | 1 | |
| 9U-5343 | Puller Stud | 1 | |
| 9U-5345 | Nut | 1 | |
| 6V-8237 | Washer | 1 | |
Start By:
- Remove the tilt cylinder. Refer to Disassembly and Assembly , "Bulldozer Tilt Cylinder (VPAT) - Remove".
- Use a suitable block on each side of the C-frame in order to support frame assembly (1).
Show/hide table
Illustration 2 g00986440 - Use a suitable block in order to support cylinder (2).
- Repeat Step 2 for the opposite side.
Show/hide table
Illustration 3 g00986441 - Install Tooling (A) and a suitable lifting device to blade assembly (3). Apply lifting tension in order to support blade assembly (3). The weight of the blade assembly is approximately
1360 kg (3000 lb) .Show/hide table
Illustration 4 g00986442 - Remove pin (4) and spacers (5).
- Repeat Step 5 for the opposite side.
Show/hide table
Illustration 5 g00986443 - Use Tooling (B) in order to remove spacer (6) and pin (7).
Show/hide table
Illustration 6 g00986444 - Remove retainer (8).
Show/hide table
Illustration 7 g00986445 - Use Tooling (C) in order to remove pin (9).
Show/hide table
Illustration 8 g00986446 - Use Tooling (E) in order to remove ring (10) from blade assembly (3), if necessary.
- Use Tooling (F) in order to remove bearing (11) from blade assembly (3), if necessary.
Show/hide table
Illustration 9 g00986569 - Use Tooling (E) in order to remove ring (12) from link assembly (13A), if necessary.
- Use Tooling (D) in order to remove bearing (13) from link assembly (13A), if necessary.
Show/hide table
| |
| Illustration 1 | g00986439 |
Information System:
2003/06/16
A New Accumulator Is Now Used {1805, 1808, 7320}
3044C Industrial Engine and Engines for Caterpillar Built Machines
Piston and Rings
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Steering Wheel - Remove and Install
953C Track-Type Loader
Specifications
994D Wheel Loader Power Train
Pump Drive (Rear) - Assemble
Repair Procedure for the Upper Hitch Assembly{7057, 7100}
651E and 657E Wheel Tractor-Scrapers Hydraulic System
Control Valve (Push-Pull)
651E and 657E Wheel Tractor-Scrapers Hydraulic System
Cushion-Hitch Circuit
3044C Industrial Engine and Engines for Caterpillar Built Machines
Engine Valve Lash - Inspect/Adjust
980G Wheel Loader Power Train
Transmission Planetary - Assemble - Standard
TH220B, TH330B and TH340B Telehandlers
Boom Wear Pad Clearance - Inspect/Adjust
980G Wheel Loader Power Train
Transmission Planetary - Disassemble - Standard
D6N Track-Type Tractor Machine Systems
Bulldozer (VPAT) - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Steering Cylinder - Remove and Install
953C Track-Type Loader
Safety Messages - Arrangement 1
2003/03/31
Correction to Testing and Adjusting , "Pilot System Pressure - Test and Adjust" {5050, 5050}
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Brake Accumulator - Remove and Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Accumulator Charging Valve (Brake) - Remove and Install
651E and 657E Wheel Tractor-Scrapers Hydraulic System
Operational Checks
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Engine Supplement
Radiator - Remove
D6N Track-Type Tractor Machine Systems
Bulldozer C-Frame - Remove
D6N Track-Type Tractor Machine Systems
Bulldozer C-Frame - Install
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Engine Supplement
Radiator - Install
651E and 657E Wheel Tractor-Scrapers Hydraulic System
Hydraulic System Troubleshooting