TH350B, TH360B, TH460B and TH560B Telehandlers Engine Supplement Engine Mount (Rear) - Remove Caterpillar


Engine Mount (Rear) - Remove
`
1.1. Removal Procedure

Removal Procedure

Start By:

  1. Remove the hood. Refer to Disassembly and Assembly, "Engine Enclosure - Remove and Install".
  2. Remove the air cleaner. Refer to Disassembly and Assembly, "Air Cleaner - Remove".

------ WARNING! ------

Personal injury or death can result from improper lifting or blocking.

When a hoist or jack is used to lift any part or component, stand clear of the area. Be sure the hoist or jack has the correct capacity to lift a component. Install blocks or stands before performance of any work under a heavy component.

Approximate weights of the components are shown. Clean all surfaces where parts are to be installed.

----------------------



    Illustration 1g00984274

  1. Attach a suitable lifting chain to the bracket on the engine and to a suitable hoist. Take up the tension on the chain but do not try to lift the engine at this time.



    Illustration 2g00984278



    Illustration 3g00984279

  1. Remove bolt (1), two washers (2), nut (3), washer (4), the lower half of mount (5) and sleeve (6) .

  1. Use the hoist to carefully lift the engine and the transmission until bracket (7) is just clear of the upper half of mount (5). The combined weight of the engine and the transmission is approximately 780 kg (1720 lb).

  1. Remove four bolts (8) and the washers in order to remove bracket (7). Remove the upper half of mount (5) from the engine frame.

Information System:

TH210 and TH215 Telehandlers Machine Systems Trailer Brake Valve (Hydraulic) - Remove and Install
TH210 and TH215 Telehandlers Machine Systems Diverter Valve - Remove and Install
TH350B, TH360B, TH460B and TH560B Telehandlers Engine Supplement Engine - Install
3034 Engine for Caterpillar Built Machines Pistons and Connecting Rods - Remove - Fractured Connecting Rod
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Piston Pump (Hydraulic Fan) - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Piston Pump (Hydraulic Fan) - Remove
D6N Track-Type Tractor Machine Systems Bulldozer Angle Cylinder (VPAT) - Remove and Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Loader Frame and Rear Frame - Connect
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Vane Pump (Braking) - Remove
3500B and 3500C Marine Engines Camshaft
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Piston and Vane Pump (Steering and Implement) - Install
3034 Engine for Caterpillar Built Machines Pistons and Connecting Rods - Install - Fractured Connecting Rod
2003/03/10 A Change to the Transmission Cover Requires a New Tube Assembly {3064}
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Pilot Operated Hydraulic Control (Joystick) - Disassemble
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Pilot Operated Hydraulic Control (Joystick) - Assemble
TH350B, TH360B, TH460B and TH560B Telehandlers Engine Supplement Engine Mount (Rear) - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Main Control Valve - Remove
651E and 657E Wheel Tractor-Scrapers Wheel Scraper Power Train Scraper Wiring Group
D6N Track-Type Tractor Machine Systems Sweeps - Remove and Install
D6N Track-Type Tractor Machine Systems Bulldozer Tilt Cylinder (VPAT) - Remove and Install
D6N Track-Type Tractor Machine Systems Bulldozer Lift Cylinder (VPAT) - Remove and Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Selector and Pressure Control Valve (Pilot) - Remove and Install
D10R Track-Type Tractor Hub Oil (Flexxaire Fan) - Change - If Equipped
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Main Control Valve - Install