D6N Track-Type Tractor Machine Systems Bulldozer Control Valve - Install Caterpillar


Bulldozer Control Valve - Install
`
1.1. Installation Procedure

Installation Procedure

Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.




    Illustration 1g00983640

  1. Install connectors (24) and fittings (23) .



    Illustration 2g00986254

  1. Attach a suitable lifting device to bulldozer control valve (22). Position bulldozer control valve (22). The weight of bulldozer control valve (22) is approximately 41 kg (90 lb).

  1. Install bolt (22A) and remove the lifting device.



    Illustration 3g00983637

  1. Install bolts (21) .



    Illustration 4g00983636

  1. Install pins (20) .



    Illustration 5g00983635

  1. Install bolt (19) .



    Illustration 6g00983633

  1. Connect fitting assembly (18) .



    Illustration 7g00983632

  1. Connect tube assembly (16). Install tube assembly (17) .



    Illustration 8g00983631

  1. Install panel (15) and screws (14) .



    Illustration 9g00983630

  1. Connect tube assembly (13) .



    Illustration 10g00983629

  1. Connect tube assemblies (12) .



    Illustration 11g00983628

  1. Connect tube assemblies (11) .



    Illustration 12g00983626

  1. Install tube assembly (10) .



    Illustration 13g00983625

  1. Connect tube assemblies (9) .



    Illustration 14g00983624

  1. Connect tube assemblies (8) .



    Illustration 15g00983622

  1. Position filter assembly (6). Install nuts (7) .



    Illustration 16g00983619

  1. Connect hose assembly (5) .



    Illustration 17g00983617

  1. Install panel (4) and bolt (3) .



    Illustration 18g00983615

  1. Install nuts (2) .



    Illustration 19g00983611

  1. Close door assembly (1) .

  1. Fill the hydraulic fluid. Refer to Operation and Maintenance, "Hydraulic System Oil - Change".

End By: Install the seat. Refer to Disassembly and Assembly, "Seat - Remove and Install".

Information System:

D6N Track-Type Tractor Machine Systems Bulldozer Control Valve - Remove
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power Train Drive Shaft (Center) - Remove and Install
980G Series II Wheel Loader Braking System Hydraulic Oil Contamination - Test
2003/03/10 Explanation of Transmission Oil Temperature Sensors {5574}
2003/03/10 The Suction Line Filter Group for the Transmission is Relocated {3016, 3067, 3154}
TH220B, TH330B and TH340B Telehandlers Caterpillar Approved Work Tools
D6R Series II Track-Type Tractor Heating and Air Conditioning Control
TH350B, TH355B, TH360B and TH460B Telehandlers Lifting Capacities
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power Train Modulating Valve (Transmission Clutch) - Install
2003/06/02 New Printer Is Used for Caterpillar Payload Control System (PCS) {749P}
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power Train Modulating Valve (Transmission Clutch) - Remove
TH350B, TH355B, TH360B and TH460B Telehandlers Longitudinal Stability Indicator - Test
D5N Track-Type Tractor Power Train Final Drive - Disassemble
D5N Track-Type Tractor Power Train Final Drive - Assemble
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Hydraulic Tank - Remove
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power Train Differential and Bevel Gear - Install
D6R Series II Track-Type Tractor Reference Material
TH210 and TH215 Telehandlers Daily Inspection
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power Train Drive Shaft (Rear) - Remove and Install
D11R Track-Type Tractor Safety Messages
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power Train Transmission and Torque Converter - Separate
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power Train Transmission and Torque Converter - Connect
953C, 963C and 973C Track-Type Loaders Transmission Electronic Control System MID 079 - CID 0248 - FMI 02
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Hydraulic Tank - Install