826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Machine Systems Hydraulic Tank - Assemble Caterpillar


Hydraulic Tank - Assemble
`
1.1. Assembly Procedure

Assembly Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 1g03722490

  1. Install screen assembly (19), the washers, and bolts (18).


    Illustration 2g03722445


    Illustration 3g03722429

  2. Install plate (16), the washers, bolts (17), the washers, and bolts (15).


    Illustration 4g03722426


    Illustration 5g03722505
    Section view

  3. Install hydraulic housing assembly (14).

    Note: Be sure that the slots on hydraulic housing assembly (14) align with Tabs (A) in inlet flange (20), as shown in Illustration 5.



    Illustration 6g03722248

  4. Install the O-ring seal and temperature sensor (13). Tighten temperature sensor (13) to a torque of 20 ± 3 N·m (177 ± 27 lb in).

  5. Install the gasket, plate assembly (12), the washers, and bolts (11).

  6. Install the O-ring seal and plug (10).


    Illustration 7g03722464

  7. Install element (9).


    Illustration 8g03722234

  8. Install O-ring seal (8) to cover (5). Install bypass valve (7) to cover (5).


    Illustration 9g03722187

  9. Install cover (5), the washers, and bolts (4). Tighten bolts (4) to a torque of 50 ± 10 N·m (37 ± 7 lb ft).

  10. Install the O-ring seal and breather (6). Tighten breather (6) to a torque of 20 ± 5 N·m (177 ± 44 lb in).


    Illustration 10g03722156

  11. Install the O-ring seals, liquid gage (2), and bolts (3). Tighten bolts (3) to a torque of 10 ± 3 N·m (89 ± 27 lb in).


    Illustration 11g03722146

  12. Install the O-ring seals and hydraulic screen assemblies (1). Tighten hydraulic screen assemblies (1) to a torque of 325 ± 45 N·m (240 ± 34 lb ft).

End By:

  1. Install the hydraulic tank.

Information System:

C3.4B Engines ECM Memory - Test
Inspect the Alternate Exit on Certain Underground Articulated Trucks and Load Haul Dump Machines{7310}
D4, D6K2 and D6K Track-Type Tractor Systems Power Train System
631K and 637K Wheel Tractor-Scraper Systems Relief Valve (Scraper Bowl) - Test and Adjust
D7E Track-Type Tractor Systems HVAC System
2014/11/27 An Improved Blower Assembly in the Air Conditioner Group Is Now Used on Certain Wheel Loaders {7320}
631K and 637K Wheel Tractor-Scraper Systems Steering System Pressure - Test and Adjust
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Machine Systems Hydraulic Tank - Disassemble
New Tube Assembly for the Low-Pressure Fuel System on Certain C6.6 Machine Engines{1261, 1274}
D4, D6K2 and D6K Track-Type Tractor Systems Additional Electrical Components
D7E Track-Type Tractor Systems Additional Electrical Components
631K and 637K Wheel Tractor-Scraper Systems Relief Valve (Steering Cylinder Crossover) - Test and Adjust
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Electrohydraulic Control
D3K2, D4K2 and D5K2 Track-Type Tractors Systems Switch Circuits - Test
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Machine Systems Piston Pump (Steering) - Remove and Install
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Location of Components (Fan Hydraulic System)
D7E Track-Type Tractor Systems Electronic Control (HVAC System)
Procedure for Installing Retrofit Radar Holder for Cat</SUP> Object Detection Systems {7347, 7605}
Installation Procedure for Mounting the Rear Radar On Certain Cat</SUP> Products{7347, 7605}
C3.4B Engines Electrical Power Supply - Test
3516E Generator Set Engine Aftercooler - Two Stage Aftercooler
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Drive Shaft
C4.4 Industrial Engine Severe Service Application
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Machine Systems Main Control Valve - Remove and Install