Trunnion Support (Oscillating Axle, Front) - Remove and Install
`
950 GC Wheel Loader Power Train
[UENR3335]
950 GC Wheel Loader Power Train
Trunnion Support (Oscillating Axle, Rear) - Remove and Install
950 GC Wheel Loader Power Train
Transmission Oil Pump - Remove
POWER TRAIN
AXLE GP
950 GC Wheel Loader Power Train
Oscillating Axle (Rear) - Remove and Install
950 GC Wheel Loader Power Train
Fixed Axle (Front) - Remove and Install
950 GC Wheel Loader Power Train
Trunnion Support (Oscillating Axle, Rear) - Remove and Install
950 GC Wheel Loader Power Train
Trunnion Support (Oscillating Axle, Front) - Remove and Install
950 GC Wheel Loader Power Train
Parking Brake - Remove and Install
950 GC Wheel Loader Power Train
Axle Housing - Disassemble
950 GC Wheel Loader Power Train
Axle Housing - Assemble
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 6V-2086 | Installer | 1 |
| 9S-8874 | Locator | 1 | |
| B | 5P-0960 | Grease Cartridge | 1 |
Start By:
- Remove the oscillating axle.
- Place the oscillating axle on suitable blocking, as shown.
- Remove yoke (1) from the differential pinion shaft.
Show/hide table
Illustration 2 g03718954 - Fasten a suitable lifting device to front trunnion support (2). Remove front trunnion support (2) from the oscillating axle. The weight of front trunnion support (2) is approximately
43 kg (95 lb) .Show/hide table
Illustration 3 g00292632 - Remove lip seal (3) from the front trunnion support. Repeat this step for the lip seal on the opposite side of the front trunnion support.
- Remove retaining ring (4) that holds sleeve bearing (5) in the front trunnion support.
- Use a suitable press and Tooling (A) to remove sleeve bearing (5) from the front trunnion support.
Show/hide table
| |
| Illustration 1 | g03718935 |
- Use a suitable press and Tooling (A) to install sleeve bearing (5) in front trunnion support (2). Make sure that the sleeve bearing contacts the counterbore in front trunnion support (2).
Show/hide table
Illustration 6 g03719387 - Use a suitable press and Tooling (A) to install lip seal (3) in both sides of the front trunnion support. Make sure that lip seal (3) contact the counterbores in the front trunnion support.
Note: Each lip seal must be installed so that the sealing lip is facing toward the outside of the front trunnion support, as shown.
- Install retaining ring (4) that holds sleeve bearing (5) in front trunnion support (2).
- Apply Tooling (B) on the sealing lips of the lip seals.
Show/hide table
Illustration 7 g03719003 - Fasten a suitable lifting device to front trunnion support (2). Install front trunnion support (2) on the oscillating axle. The weight of front trunnion support (2) is approximately
43 kg (95 lb) .Show/hide table
Illustration 8 g03719010 - Install yoke (1) on the differential pinion shaft.
Show/hide table
| |
| Illustration 4 | g00292633 |
|
(3) Lip Seal. (4) Retaining Ring. (5) Sleeve Bearing. | |
Show/hide table
| |
| Illustration 5 | g03719356 |
End By:
- Install the oscillating axle.
Information System:
980L Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems
Transmission Speed for Reverse Directional Shift - Program
980L Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems
Transmission Speed for Forward Directional Shift - Program
C175-16 Locomotive Engine
Configuration Parameters
D4, D6K2 and D6K Track-Type Tractor Systems
Electronic Control (Hydraulic System)
2014/10/16
New Ejector Cylinder Group is Now Used on Certain 631G and 637G Wheel Tractor-Scrapers {5305}
D7E Track-Type Tractor Systems
Electronic Control (Power Train System)
Fast Fill Hose Inspection On Certain D8TTrack-Type Tractors Equipped With a Fast Fuel Attachment{1273, 1710}
C280 Marine Engines
Secondary ECM Assumes Control
3500E EPA Tier 4 Final and IMO-II/III Switchable Marine Engines
Engine Control Switch - Test
3516B Generator Set Engines with Dynamic Gas Blending
Intake Manifold Air Temperature Is High
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems
Steering Control Valve
D7E Track-Type Tractor
Engine Oil and Filter - Change
3512E Petroleum Engines
Engine Governing - Adjust
Relocation Procedure of the Engine Outlet NOx Sensor On Certain 834K, 836K, and 988K Machines{7490}
2014/10/23
Improved Woodchip Screens are now used on D8T Track-Type Tractors Equipped with Quick Release Radiator Grills {7170}
986H Wheel Loader
Differential and Bevel Gear - Disassemble
Instrument Display Turn Signal Indicators Do Not Blink When the Signal Switch is Activated{1430}
Procedure to Install LED Lights on AD30 Underground Articulated Trucks{1429, 1434}
2014/09/05
Water In Fuel Sensor Wiring on Certain C3.4B Engines {1408, 7422}
525D, 535D, 545D and 555D Wheel Skidders C7.1 Engine Supplement
System Pressure - Release
2014/09/05
Cat Reman Has Added Valve Actuators, Valve Lifters, Rocker Arms, and Camshafts for Certain Machine Engines {1121, 1130, 1209, 1210}
2014/09/05
Cat Reman Announces New Fuel Pump, Fuel Ratio Control, and Fuel Injector Options for Certain Engines {1251, 1278}
2014/09/04
Cat Reman Announces New Fuel Pump, Fuel Ratio Control, and Fuel Injector Options for Certain Machine Engines {1251, 1278}
Installation Procedure of <NOBR>469-0108</NOBR> Kit Utility Mounting Brackets Inside the Cab of Certain Medium Wheel Loaders {7301}