826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Engine Supplement Engine Oil Cooler - Remove and Install Caterpillar


Engine Oil Cooler - Remove and Install
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Start By:

  1. Remove the crankcase guard.


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.

Dispose of all fluids according to local regulations and mandates.


  1. Drain the coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change" for the correct draining and filling procedures.


    Illustration 1g03713032

  2. Open door (1).


    Illustration 2g03712601
    Typical Example

  3. Remove panel (2).


    Illustration 3g03713121

  4. Remove clips (3).

  5. Disconnect hoses (4).

  6. Disconnect hose assembly (5).

  7. Remove hose assemblies (6).

  8. Disconnect harness assembly (7).


    Illustration 4g03713151

  9. Remove bolts (8) and the washers. Remove bonnet (9), the gaskets, and the O-ring seal.


    Illustration 5g03713190
    Viewed from beneath the machine.

  10. Remove bolts (10) and bolts (11) and the washers.


    Illustration 6g03713199

  11. Remove engine oil cooler (12) and the O-ring seals.

Installation Procedure

  1. Install engine oil cooler (12) in the reverse order of removal.

    1. Lubricate the bore at both ends of engine oil cooler (12) with the lubricant that is being sealed.

Information System:

2014/09/12 The Fender Support Mount Has Been Improved on Certain Wheel Tractor-Scrapers {7050}
D5R2 and D6R2 Track-Type Tractors Determining Diagnostic Trouble Codes
D5R2 and D6R2 Track-Type Tractors Electrical Connector - Inspect
D3K2, D4K2 and D5K2 Track-Type Tractors Systems Implement System
986H Wheel Loader Final Drive and Wheel - Remove and Install
D6R2 Track-Type Tractor Systems Calibration Error Codes
D6R2 Track-Type Tractor Systems Calibrations (Cat ET)
C3.4B Engines DEF Does Not Purge
D3K2, D4K2 and D5K2 Track-Type Tractors Systems Fast Fill Fuel System
986H Wheel Loader Service Brake - Remove and Install
986H Wheel Loader Final Drive, Brake, Wheel, and Spindle - Remove and Install
D5R2 and D6R2 Track-Type Tractors Service Tools
986H Wheel Loader Final Drive (Planetary) - Assemble
986H Wheel Loader Oscillating Axle (Rear) - Remove and Install
950 GC Wheel Loader Engine Supplement Engine - Remove and Install
3500E Marine Engines Engine Oil Lines
C3.4B Engines DEF Pressure Does Not Respond
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Engine Supplement Aftercooler - Remove and Install
D5R2 and D6R2 Track-Type Tractors Wiring Harness (Short Circuit) - Test
950M and 962M Wheel Loaders Mounting and Dismounting
906K, 906M, 907K, 907M, 908K and 908M Compact Wheel Loaders Electrohydraulic System Diagnostic Trouble Codes
D6N Track-Type Tractor Systems Piston Pump (Implement)
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Engine Supplement Aftercooler - Remove and Install
D5R2 Track-Type Tractor Systems Line Relief and Makeup Valve