826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Engine Supplement Engine Oil Filter and Oil Filter Base - Remove and Install Caterpillar


Engine Oil Filter and Oil Filter Base - Remove and Install
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
185-3630  Strap Wrench As 


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.

Dispose of all fluids according to local regulations and mandates.




    Illustration 1g03648876

  1. Open door (1).


    Illustration 2g03712514

  2. Use Tooling (A) in order to remove engine oil filter (5). Refer to Operation and Maintenance Manual, "Engine Oil Filter - Change" for the correct draining procedure.

  3. Disconnect hose assemblies (2).

  4. Remove bolts (3) and the washers. Remove engine oil filter base (4).


    Illustration 3g03712524

  5. Remove cup plug (6), fittings (7) and the O-ring seals from engine oil filter base (4). Remove fitting (8), plug (9), and the O-ring seals.


    Illustration 4g03712528

    ------ WARNING! ------

    Personal injury can result from being struck by parts propelled by a released spring force.

    Make sure to wear all necessary protective equipment.

    Follow the recommended procedure and use all recommended tooling to release the spring force.


  6. Remove plug (15) from engine oil filter base (4). Remove O-ring seal (14) from plug (15).

  7. Remove plug (13). Remove O-ring seal (12) from plug (13). Remove spring (11) and relief valve plunger (10).

Installation Procedure

  1. Install engine oil filter base (4) and engine oil filter (5) in the reverse order of removal.

    1. Install a new engine oil filter (5). Refer to Operation and Maintenance Manual, "Engine Oil Filter - Change" for the correct filling procedure.

Information System:

D6N Track-Type Tractor Location of Components (HVAC System)
950 GC Wheel Loader Machine Systems Refrigerant Receiver-Dryer - Remove and Install
D5R2 and D6R2 Track-Type Tractors General Information
986H Wheel Loader Fixed Axle (Front) - Remove and Install
926M, 930M, and 938M Small Wheel Loader Diesel Exhaust Fluid Filter - Replace
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Engine Supplement Hydraulic Oil Cooler - Remove and Install
D6N Track-Type Tractor HVAC System
986H Wheel Loader Axle Shaft - Remove and Install
Installation of 7S (S/N: RL7) and 7SU (S/N: RT7) on D7R Track-Type Tractor{6050, 6051, 6060, 6078}
950 GC Wheel Loader Machine Systems Refrigerant Condenser - Remove and Install
Installation of No. 7 Ripper (RMP) on D7R Track-Type Tractor{6310, 6324, 6325}
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Engine Supplement Fuel Cooler - Remove and Install
D5R2 and D6R2 Track-Type Tractors Machine Preparation for Troubleshooting
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Engine Supplement Engine Oil Cooler - Remove and Install
D5R2 and D6R2 Track-Type Tractors Visual Inspection
2014/10/20 New Product Link and VIMS 3G Software for 523 and A4:N4 Modules Is Now Available for Certain Series M and Series K Wheel Loaders {7601, 7606, 7620}
C3.4B Engines DEF Pressure Is High
Differential Retrofit for the 990H Front Axle{3258}
D5R2 and D6R2 Track-Type Tractors Service Tools
986H Wheel Loader Final Drive, Brake, Wheel, and Spindle - Remove and Install
986H Wheel Loader Service Brake - Remove and Install
D3K2, D4K2 and D5K2 Track-Type Tractors Systems Fast Fill Fuel System
C3.4B Engines DEF Does Not Purge
D6R2 Track-Type Tractor Systems Calibrations (Cat ET)