Flywheel - Remove and Install
`
C15 and C18 Engines for Caterpillar Built Machines
[UENR0132]
C15 and C18 Engines for Caterpillar Built Machines
Inlet and Exhaust Valve Springs - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines
Engine Oil Filter Base - Remove and Install
BASIC ENGINE
FLYWHEEL GP
C15 and C18 Engines for Caterpillar Built Machines
Flywheel - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 439-3938 | Lifting Bracket | 2 |
B | FT2712 | Guide Stud | 2 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install Tooling (A) on the flywheel. Use a suitable lifting device. The weight of the flywheel is approximately
40 kg (88 lb) . - Remove two bolts (1). Install Tooling (B).
- Remove remaining bolts (1) that hold the flywheel to the crankshaft . Remove flywheel (2).
Show/hide table
Illustration 2 g01953204 - If necessary, use a hammer and a punch to remove ring gear (3) from the flywheel.
Show/hide table
Illustration 1 | g01953202 |
- Install flywheel (2) in the reverse order of removal.
- Tighten bolts (1) to a torque of
270 ± 40 N·m (200 ± 30 lb ft) .
Information System:
C9.3 Engines for Caterpillar Built Machines
Soot Antenna - Remove and Install
AD30 Underground Articulated Truck
Safety Messages
Installation of the CAES ARO Groups{7604}
D6T Track-Type Tractor
Camera - Clean/Adjust
14L Motor Grader
Water Pump - Remove and Install
C9.3 Engines for Caterpillar Built Machines
Engine Oil Cooler - Remove and Install
2009/08/31
A New Alternator Is Available for the Tier III 657G Wheel Tractor-Scraper Tractor Engines {1405}
Damaged Liner Seals on 3400 Reman Cylinder Packs {1201, 1216, 1239}
2009/08/31
A New Alternator Is Available for the Tier III 631G and the Tier III 637GWheel Tractor-Scraper Tractor Engines {1405}
Torque Converter Failures on Certain Telehandler Machines{3101, 5056}
C9.3 Engines for Caterpillar Built Machines
Fuel Injection Pump - Remove and Install
Work Tool (Custom) 348-4916 Lumber Fork
Rated Load
D7E Track-Type Tractor Hydraulic, HVAC, and Electrical Systems
Implement Movement Without Request
2010/02/03
A New "B" Pin Bearing Has Been Designed for the Bucket of Medium Wheel Loaders that Are Used As Steel Mill Machines Working in Severe Applications {6107, 7000}
Procedure to Improve the Starting Capability on 627G and 637G Wheel Tractor-Scrapers{0645, 1456, 1920, 7620}
C13, C15, and C18 Tier 4 Interim Engines
ARD Temperature Is Low
953D, 963D and 973D Track-Type Loaders
Hydraulic System Pressure Is Low
966H and 972H Wheel Loaders
Declaration of Conformity
IT38H Integrated Toolcarrier and 938H Wheel Loader
Declaration of Conformity
C9.3 Tier 4 Final Engines
Diesel Particulate Filter Has High Ash Load
D7E Track-Type Tractor Hydraulic, HVAC, and Electrical Systems
Implement Droops Before Raising
2009/10/01
A New Slip Joint Group Improves Service Life of the Drive Shaft {3251}
953D, 963D and 973D Track-Type Loaders
Hydraulic System Hesitates
953D, 963D and 973D Track-Type Loaders
Machine Movement Is Unstable