Temperature Sensor (DPF) - Remove and Install
`
C9.3 <BR>Engines for Caterpillar Built Machines
[KENR8149]
C9.3 Engines for Caterpillar Built Machines
Flame Detection Temperature Sensor - Remove and Install
C9.3 Engines for Caterpillar Built Machines
Air Cleaner Housing - Remove and Install
ELECTRICAL AND STARTING SYSTEM
SENSOR GP
C9.3 Engines for Caterpillar Built Machines
Speed/Timing Sensor - Remove and Install
C9.3 Engines for Caterpillar Built Machines
Fuel Pressure Sensor - Remove and Install - Rail
C9.3 Engines for Caterpillar Built Machines
Coolant Temperature Sensor - Remove and Install
C9.3 Engines for Caterpillar Built Machines
Flame Detection Temperature Sensor - Remove and Install
C9.3 Engines for Caterpillar Built Machines
Temperature Sensor (DPF) - Remove and Install
C9.3 Engines for Caterpillar Built Machines
Soot Antenna - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | - | Loctite 771 Anti-Seize Compound | - |
- Remove cable straps (1) and remove flame detection temperature sensor (2).
Show/hide table
Illustration 2 g02833596 - Remove cable straps (4) and disconnect harness assembly (5).
- Remove the inlet temperature sensor (3), which is located on the diesel particulate filter.
Show/hide table
| |
| Illustration 1 | g02154117 |
- Install the flame detection temperature sensor in the reverse order.
- Apply Tooling (A) to the threads on flame detection temperature sensor (2) and to the threads of inlet temperature sensor (3). Tighten the flame detection temperature sensor (2) and the inlet temperature sensor (3) to a torque of
45 ± 5 N·m (33 ± 4 lb ft) .
- Apply Tooling (A) to the threads on flame detection temperature sensor (2) and to the threads of inlet temperature sensor (3). Tighten the flame detection temperature sensor (2) and the inlet temperature sensor (3) to a torque of
Information System:
Pivot Shaft Seal Leaks On D6K, D6N, And Track-Type Loaders{4153}
C9.3 Engines for Caterpillar Built Machines
Flame Detection Temperature Sensor - Remove and Install
3512B, 3512C, and 3516B Generator Set Engines with Dynamic Gas Blending
Air Starting System
C13, C15, and C18 Tier 4 Interim Engines
Sensor Supply - Test
C4.4 Industrial Engine
Piston Height - Inspect
C3.4B Engines for Caterpillar Built Machines
Piston Ring Groove - Inspect
973D Track-Type Loader Power Train
Brake and Final Drive Group
973D Track-Type Loader Power Train
Tracks
953D, 963D and 973D Track-Type Loaders
Brake Does Not Release
C9.3 Engines for Caterpillar Built Machines
Nozzle Heater Harness - Remove and Install - Harness Assembly
953D, 963D and 973D Track-Type Loaders
Backup Alarm Does Not Function
D7E Track-Type Tractor Hydraulic, HVAC, and Electrical Systems
Hydraulic Fan Speed (On Demand) - Test and Adjust
2009/07/06
New AMOCS Seals That Are Between the Radiator Core and the Tank Are Now Available on Certain Track-Type Tractors and Pipelayers {1353}
3500 Engines
Exhaust Elbow - Remove and Install
D8T Track-Type Tractor
Declaration of Conformity
D10T Track-Type Tractor
Declaration of Conformity
D9T Track-Type Tractor
Declaration of Conformity
Installation of the Angling Blade Bulldozer on the D7E Track-Type Tractor{6050, 6701}
3500 Engines
Exhaust Manifold - Remove and Install
953D, 963D and 973D Track-Type Loaders
Hydraulic System Has Unusual Noise
C9.3 Engines for Caterpillar Built Machines
Air Cleaner Housing - Remove and Install
D6T Track-Type Tractor Systems
Pressure Reducing Valve - Test and Adjust
C13, C15, and C18 Tier 4 Interim Engines
ARD Does Not Activate
C9.3 Engines for Caterpillar Built Machines
Diesel Particulate Filter - Remove and Install - Diesel Oxidation Catalyst, Clean Emissions Module