Lubrication Pump (Automatic) - Assemble
`
966H and 972H Wheel Loaders Machine Systems
[RENR8859]
966H and 972H Wheel Loaders Machine Systems
Pilot Valve (Command Control Steering) - Assemble
966H and 972H Wheel Loaders Machine Systems
Lubrication Pump (Automatic) - Disassemble
FRAME AND BODY
LUBRICATION GP
966H and 972H Wheel Loaders Machine Systems
Lubrication Pump (Automatic) - Assemble
966H and 972H Wheel Loaders Machine Systems
Lubrication Pump (Automatic) - Disassemble
1.1. Assembly Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Assemble the valve and the coil of valve (16) together before securing the parts with ring (17).
Show/hide table
Illustration 2 g01943717 - Install valve (16) onto pump assembly (14).
Show/hide table
Illustration 3 g01943720 Show/hide tableIllustration 4 g01943721 - Install O-ring seal (15) to pump assembly (14) before installing the pump assembly into base (5). Connect the harness assembly for the pump assembly to the base.
Show/hide table
Illustration 5 g01943723 - Install gasket (13) into cover (12).
Show/hide table
Illustration 6 g01943725 - Install cover (12) onto base (5).
Show/hide table
Illustration 7 g01943730 - Install harness assembly (11) into base (5).
Show/hide table
Illustration 8 g01943732 - Install grid (10) into base (5) before installing mixing gear (9).
Show/hide table
Illustration 9 g01943733 - Install bridge (8) into base (5).
Show/hide table
Illustration 10 g01943735 Show/hide tableIllustration 11 g01943736 - Install plate (7) and the spring.
- Use a suitable dowel to install guide pin (6) and the washer into base (5).
Note: Do not use any tools to grip on the outside of the guide pin.
Show/hide tableIllustration 12 g01943819 - Install lubrication tank (4) onto base (5).
Show/hide table
Illustration 13 g01943824 - Install the seal into cover (1). Turn over the lubrication pump and install the lubrication pump onto the cover.
Show/hide table
Illustration 14 g01943826 - Carefully turn over the lubrication pump and install the O-ring seal. Secure cover (1) in place with nut (3).
Show/hide table
Illustration 15 g01943827 - Install plug (2) into cover (1).
- Install the lubrication pump onto the machine.
Show/hide table
![]() | |
Illustration 1 | g01943715 |
Information System:
Generator Bearing Service {4457}
973D Track-Type Loader Power Train
Track Roller
C4.4 Industrial Engine
Refrigerant Compressor
2009/06/29
An Improved Adjustable Armrest Is Now Available {7307}
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735B, 735C, 740B, 740B Ejector, 740C Ejector and 745C Articulated Trucks VIMSTM</SUP> 3G
Using Caterpillar Electronic Technician to Determine Diagnostic Codes
973D Track-Type Loader Power Train
General Information
2009/07/06
The Undercarriage Has Been Changed To Camber Only {4150}
973D Track-Type Loader Hydraulic System
Location of Electrical Components
2009/08/10
An Improved Engine Oil Pump Assembly Is Used {1304}
Procedure To Rework the Torque Converter and Updrive Housing Speed Sensor Mount{3101, 3159, 3175}
D6K Track-Type Tractor Machine Systems
Pump Mounting - Remove and Install
C13, C15, and C18 Tier 4 Interim Engines
ARD Ignition - Test
966H and 972H Wheel Loaders Machine Systems
Lubrication Pump (Automatic) - Disassemble
973D Track-Type Loader Power Train
Hydrostatic Drive Motor
C6.6 Industrial Engine
Exhaust Gas Valve (NRS)
2009/06/29
Improvements to the Lines Group for the Lift Cylinder on 938H and IT38H Machines {5057, 5102}
C9.3 Engines for Caterpillar Built Machines
Engine Control Module - Remove and Install
973D Track-Type Loader Power Train
Location of Electrical Components
973 K Track-Type Loaders
Equalizer Bar
973 K Track-Type Loaders
Front Idler and Recoil Spring
3500 Engines
Prelubrication Oil Pump - Remove and Install
3500 Engines
Electronic Control Module (Engine) - Remove and Install
2009/07/06
Water Temperature Regulators (Thermostats) Have Been Redesigned {1355, 1380, 1393}
2009/07/01
Water Temperature Regulators (Thermostats) Have Been Redesigned {1355, 1380, 1393}