EPC Parts Catalogs

C9.3 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install Caterpillar


  1. Home
  2. Disassembly and Assembly
  3. #127070
Engine Oil Pan - Remove and Install
`
C9.3 <BR>Engines for Caterpillar Built Machines [KENR8149]
C9.3 Engines for Caterpillar Built Machines Turbocharger - Remove and Install - Cooled by Coolant
C9.3 Engines for Caterpillar Built Machines Relay (ARD Nozzle Heater) - Remove and Install - Clean Emissions Module
BASIC ENGINE
PAN GP-OIL
C9.3 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

  1. Drain the engine oil into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual for the correct procedure.
    Show/hide table

    Illustration 1g02141944

  1. Remove bolts (1) and (3) .

  1. Loosen fitting (4) and remove oil gauge (2) .
    Show/hide table

    Illustration 2g02141932

  1. Remove nuts (5) . Remove switch assembly (6) . Remove sound suppression cover (7) .
    Show/hide table

    Illustration 3g02141942

    Note: Do not pry or gouge the sealing surface of the engine oil pan. Use a rubber mallet to tap lightly on the engine oil pan, if necessary.

  1. Remove bolts (8) . Remove studs (9) . Remove engine oil pan (10) and the gasket.

Installation Procedure

Show/hide table
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     -     Loctite 587     -    
    Show/hide table

    Illustration 4g02142246

  1. Tooling (A) should be applied at Locations (X) for a width of 4.00 ± 1.00 mm (0.158 ± 0.040 inch). Apply Tooling (A) to the joints.
    Show/hide table

    Illustration 5g02141942
    Show/hide table

    Illustration 6g02142370

  1. Position a new gasket and engine oil pan (10) on the cylinder block.

  1. Install studs (8) . Install bolts (9) . Install bolts (9) .
    Show/hide table

    Illustration 7g02143244

    Top View of Engine

    Tightening sequence for the engine oil pan

  1. Tighten studs (8) and tighten bolts (9) in the sequence that is shown in illustration 7.
    Show/hide table

    Illustration 8g02141932

  1. Install sound suppression cover (7) . Install nuts (5) . Install switch assembly (6) .
    Show/hide table

    Illustration 9g02141944

  1. Position oil gauge (2) and tighten fitting (4) .

  1. Install bolts (1) and (3) .

  1. Fill the engine with oil to the correct level. Refer to Operation and Maintenance Manual, "Engine Oil - Change" for the correct filling procedure.

Information System:

Undersized Front Track Roller Frame Bearing{4151}
2009/06/15 Improved Hardware and Software for the Impeller Clutch on the 993K Torque Converter {1365, 3004, 3067, 3101, 4800, 4808, 7610, 7620}
950H Wheel Loader, 962H Wheel Loader and IT62H Integrated Toolcarrier Power Train Transmission Planetary
D6T Track-Type Tractor Hydraulic System Lift Cylinder (Bulldozer)
973 K Track-Type Loaders Lift Cylinder
Installation and Initial Start-Up Procedure for Certain Engines {1000}
3304B and 3306B Engines for Caterpillar Built Machines Engine Oil Pump - Assemble
2009/11/16 New Window Washer Tank Group is Available for Certain Wheel Tractor-Scrapers {7306}
Installation of the Payload Monitoring System in Certain Wheel Loaders {7494}
Rework Procedure To Update the Radiator Group{1353, 7251}
C15 and C18 Tier 4 Final Engines General Information
C7.1 Industrial Engine Exhaust Combustion (ARD) - Aftertreatment Regeneration Device
C15 and C18 Tier 4 Final Engines Lubrication System
2009/10/01 A New Gasket and Hardware Are Used for the Water Lines In Some 3500 and G3500 Engines {1052, 1380}
D7R Series II Track-Type Tractor Engine Air Filter Primary and/or Secondary Element - Clean/Replace
973D Track-Type Loader Hydraulic System Ripper Cylinder
973D Track-Type Loader Hydraulic System Bucket Control Group
C15 and C18 Tier 4 Final Engines Basic Engine
C15 and C18 Tier 4 Final Engines Cooling System
973D Track-Type Loader Power Train Power Train Electrohydraulic System
Undercarriage Reconditioning Bulletin Contents {0374, 4150}
2009/06/15 A New Cover Plate For the Bottom Guard Is Now Used {7153}
980H Wheel Loader Machine Systems Lubrication Pump (Automatic) - Disassemble
980H Wheel Loader Machine Systems Lubrication Pump (Automatic) - Assemble