Fuel Transfer Pump - Remove and Install
`
C9.3 <BR>Engines for Caterpillar Built Machines
[KENR8149]
C9.3 Engines for Caterpillar Built Machines
Fuel Filter Base - Remove and Install
C9.3 Engines for Caterpillar Built Machines
Relief Valve (Fuel) - Remove and Install
FUEL SYSTEM
PUMP GP-FUEL TRANSFER
Start By:
- Remove the fuel injection pump.
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove nuts (1) and nut (3). Remove plate (4) and bracket assembly (2).
Show/hide table
Illustration 2 g03348110 - Remove bolts (5) and studs (6).
- Remove connectors (7) and the O-ring seals.
Show/hide table
| |
| Illustration 1 | g03348107 |
- Install the fuel transfer pump in the reverse order.
- Torque bolts (5) and studs (6) to a torque of
30 ± 4 N·m (22 ± 3 lb ft) .
- Torque bolts (5) and studs (6) to a torque of
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Information System:
2009/05/25
Correction to the Operation and Maintenance Manual , "Engine Air Filter Primary Element - Clean/Replace" {1054}
C13, C15, and C18 Tier 4 Interim Engines
Event Codes
C13, C15, and C18 Tier 4 Interim Engines
Diagnostic Trouble Codes
C9.3 Tier 4 Final Engines
Fuel Filter Base
C9.3 Tier 4 Final Engines
Air Inlet and Exhaust System
C9.3 Tier 4 Final Engines
Fuel System
904H Compact Wheel Loader
Maintenance Interval Schedule
C9.3 Engines for Caterpillar Built Machines
Test ECM Mode
C9.3 Engines for Caterpillar Built Machines
Electronic Service Tool Does Not Communicate
C13, C15, and C18 Engines for Caterpillar Built Machines
Factory Passwords
D7E Track-Type Tractor Power Train
Track - Connect - SystemOne Track
C13, C15, and C18 Tier 4 Interim Engines
Component Location
C11 and C13 Engines
Cylinder Head Valves
D5R Track-Type Tractor
Steering Is Harsh
2009/05/25
Correction to the Service Manual , "Ejector Body" {7258}
Procedure For Replacing The Harness Between The Chassis And The Hitch{1408}
C9.3 Engines for Caterpillar Built Machines
Fuel Lines - Remove and Install
2009/08/17
A Hotline for the Fuel Systems for Hydraulic Electronic Unit Injectors (HEUI) Is Now Available. {1251, 1290}
AccuGrade GPS / Single UTS / Site and Laser Reference v11 for Excavators
Excavator Arm Sensors - Calibrate - PSC System
3516B Engine for 994F and 994H Wheel Loaders
Power Is Intermittently Low or Power Cutout Is Intermittent
2009/05/25
Correction to the Disassembly and Assembly , "Tailgate - Remove" {7250, 7271}
2009/05/25
Correction to the Disassembly and Assembly , "Tailgate - Install" {7250, 7271}
2009/06/29
Fuel Injection Pump Latch Valve for 3054C Engines {1251}
621G Wheel Tractor-Scraper
Declaration of Conformity