Track - Connect - SystemOne Track
`
D7E Track-Type Tractor Power Train
[KENR5162]
D7E Track-Type Tractor Power Train
Track Roller Frame - Remove and Install
D7E Track-Type Tractor Power Train
Axle - Remove and Install - Outer Axle
UNDERCARRIAGE
TRACK GP
D7E Track-Type Tractor Power Train
Track - Separate - Heavy Duty Track
D7E Track-Type Tractor Power Train
Track - Connect - Heavy Duty Track
D7E Track-Type Tractor Power Train
Track - Connect - SystemOne Track
1.1. Connection Procedure
Connection Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 308-3470     | Jack Stand Gp     | 1     |
B     | 260-9412     | Chain As     | 1     |
C     | 4C-5593     | Anti-Seize Compound     | -     |
- Attach Tooling (B) in order to position the track.
Show/hide table
![]() | |
Illustration 1 | g01917978 |
Show/hide table
![]() | |
Illustration 2 | g01962013 |
Note: Check the location of marking (X) on the ends of the cartridge pin. The marking on the cartridge pin should be perpendicular to the rail of the outer track link that will be pushed. If the orientation is not correct, rotate the cartridge pin to the correct position.
Note: The cartridge pin and clamp master links must be free of paint and debris.
- Apply Tooling (C) to bores of clamp master links (5) and the collars of the cartridge pins. Install clamp master links (5) .
- Use two people in order to install track shoe (4) . The weight of track shoe (2) is approximately 27 kg (60 lb). Apply Tooling (C) to the threads and face of bolts (3) . Install track shoe (4) and bolts (3) . Tighten bolts (3) in numerical order. Tighten bolts (3) to a torque of 550 ± 70 N·m (405 ± 50 lb ft). Tighten bolts (3) to an additional turn of 180 degrees.
Show/hide table
![]() | |
Illustration 3 | g01917977 |
Show/hide table
![]() | |
Illustration 4 | g01918133 |
Note: Do not reuse track bolts. Because the track bolts have been torqued to a yield, the bolts can only be used one time. Failure to replace the track bolts with new track bolts could result in damage to the machine.
- Remove Tooling (A) .
Show/hide table
![]() | |
Illustration 5 | g01876457 |
- Tighten relief valve (2) . Tighten relief valve (2) to a torque of 34 ± 7 N·m (25 ± 5 lb ft).
Show/hide table
![]() | |
Illustration 6 | g01876456 |
- Tighten the track tension. Refer to Operation and Maintenance Manual, "Track - Check/Adjust".
- Install cover (1) .
Show/hide table
![]() | |
Illustration 7 | g01876455 |
Information System:
C13, C15, and C18 Tier 4 Interim Engines
Component Location
C13 Engine for Caterpillar Built Machines
Engine Control Module - Remove and Install
C13, C15, and C18 Tier 4 Interim Engines
Exhaust Temperature Is High
C11, C13, C15, and C18 Industrial Engines
Exhaust System Contains Oil
C9.3 Engines for Caterpillar Built Machines
Crankcase Fumes Disposal Tube Has Oil Draining
C13, C15, and C18 Tier 4 Interim Engines
System Overview
C11, C13, C15, and C18 Industrial Engines
General Information
C13 Engines for Caterpillar Built Machines
Air Cleaner - Remove and Install
C13, C15, and C18 Tier 4 Interim Engines
Fuel Consumption Is Excessive
C9.3 Engines for Caterpillar Built Machines
Fuel Filter Is Restricted
C15 and C18 Tier 4 Final Engines
Air Inlet and Exhaust System
C3.4B Industrial Engine
Cold Weather Starting
C13, C15, and C18 Engines for Caterpillar Built Machines
Factory Passwords
C9.3 Engines for Caterpillar Built Machines
Electronic Service Tool Does Not Communicate
C9.3 Engines for Caterpillar Built Machines
Test ECM Mode
904H Compact Wheel Loader
Maintenance Interval Schedule
C9.3 Tier 4 Final Engines
Fuel System
C9.3 Tier 4 Final Engines
Air Inlet and Exhaust System
C9.3 Tier 4 Final Engines
Fuel Filter Base
C13, C15, and C18 Tier 4 Interim Engines
Diagnostic Trouble Codes
C13, C15, and C18 Tier 4 Interim Engines
Event Codes
2009/05/25
Correction to the Operation and Maintenance Manual , "Engine Air Filter Primary Element - Clean/Replace" {1054}
C9.3 Engines for Caterpillar Built Machines
Fuel Transfer Pump - Remove and Install
C11 and C13 Engines
Cylinder Head Valves