Muffler - Remove and Install - Clean Emissions Module
`
C13 <BR>Engines for Caterpillar Built Machines
[KENR8150]
C13 Engines for Caterpillar Built Machines
Temperature Sensor (DPF) - Remove and Install - Clean Emissions Module
C13 Engines for Caterpillar Built Machines
Air Cleaner - Remove and Install
AIR INLET AND EXHAUST SYSTEM
EXHAUST GP
C13 Engines for Caterpillar Built Machines
Exhaust Manifold - Remove and Install
C13 Engines for Caterpillar Built Machines
Exhaust Cooler (NRS) - Remove and Install
C13 Engines for Caterpillar Built Machines
Exhaust Sensor Lines - Remove and Install - Venturi
C13 Engines for Caterpillar Built Machines
Combustion Head - Remove and Install - Clean Emissions Module
C13 Engines for Caterpillar Built Machines
Flame Detection Temperature Sensor - Remove and Install - Clean Emissions Module
C13 Engines for Caterpillar Built Machines
Diesel Particulate Filter - Remove and Install - Clean Emissions Module
C13 Engines for Caterpillar Built Machines
Catalyst - Remove and Install - Diesel Oxidation Catalyst, Clean Emissions Module
1.1. Removal Procedure
2.1. Installation Procedure
- Attach a suitable lifting device to bracket (2) and the air cleaner. The weight of bracket (2) and the air cleaner is approximately
43 kg (95 lb) . - Remove bolts (1).
Show/hide table
Illustration 2 g01904473 - Remove bolts (3), bracket (2), and the air cleaner.
Show/hide table
Illustration 3 g01904474 - Remove clamp (4).
- Attach a suitable lifting device to muffler (6). The weight of muffler (6) is approximately
50 kg (110 lb) . Disconnect clamp assemblies (5) and reposition clamp assemblies (5). Remove muffler (6).
Show/hide table
![]() | |
Illustration 1 | g01904422 |
- Install muffler (6) in reverse order of removal.
- Tighten clamp (4) to a torque of
12 ± 1 N·m (106 ± 9 lb in) . Use hand tools in order to tighten clamp assemblies (5).
- Tighten clamp (4) to a torque of
Information System:
C9.3 Engines for Caterpillar Built Machines
Exhaust Manifold - Remove and Install
2009/05/04
Improved Installation Procedure for the Heater Cable {7304}
Improved Method for Installing the Actual Gear Position Sensor {1439, 3061}
2009/10/29
A New Bowl for the Fuel/Water Separator Is Used {1261, 1263}
Installation of Ripper (3TP){6310}
Oversized Injector Sleeves for Remanufactured Cylinder Heads On Medium Sized Engines{1100, 1101, 1125}
C13 Engines for Caterpillar Built Machines
Temperature Sensor (DPF) - Remove and Install - Clean Emissions Module
Installation and Removal of the V-PAT Bulldozer{6050, 6079}
C13 Engines for Caterpillar Built Machines
Catalyst - Remove and Install - Diesel Oxidation Catalyst, Clean Emissions Module
D6T Track-Type Tractor Hydraulic System
Pressure Taps
C13 Engines for Caterpillar Built Machines
Diesel Particulate Filter - Remove and Install - Clean Emissions Module
C13 Engines for Caterpillar Built Machines
Flame Detection Temperature Sensor - Remove and Install - Clean Emissions Module
C13, C15, and C18 Tier 4 Interim Engines
Injector Solenoid - Test
C9.3 Engines for Caterpillar Built Machines
Fuel Injection Pump - Test
D6T Track-Type Tractor Hydraulic System
Operational Checks
D6T Track-Type Tractor Systems
Piston Pump (Implement) - Test and Adjust
2009/05/04
A Tilt Regeneration Kit Is Now Available for the 988G and 988H Machines {1408, 5057, 5104, 512R}
D6T Track-Type Tractor Systems
Accumulator (Pilot) - Test and Charge
3500 Engines
Turbocharger
3500 Engines
Air Inlet and Exhaust Lines
3500 Engines
Air Lines
C4.4 Industrial Engine
Air in Fuel - Test
C7.1 Industrial Engine
Fuel Injection Timing - Check
C4.4 Industrial Engine
Compression - Test