834H Wheel Dozer and 836H Landfill Compactor Machine Systems Push Arms and Blade - Install Caterpillar


Push Arms and Blade - Install
`
834H Wheel Dozer and <BR> 836H Landfill Compactor Machine Systems [RENR6224]
WORK TOOLS
BLADE GP
834H Wheel Dozer and 836H Landfill Compactor Machine Systems Push Arms and Blade - Remove
834H Wheel Dozer and 836H Landfill Compactor Machine Systems Push Arms and Blade - Install
1.1. Installation Procedure

Installation Procedure




    Illustration 1g01901755

  1. Move the machine in position between push arms (9) .

  1. Move the machine ahead until push arms (9) engage with the trunnion .



    Illustration 2g01901054

  1. Install bolts (10) and cap (11) without the shims.

  1. Tighten bolts (10) evenly.

  1. Insert an equal amount of shims between the cap and the push arm assembly, as needed.

  1. Add one additional shim to each of the spaces. The specified clearance between the trunnion and the push arm assembly is 0.2 mm (0.008 inch) to 1.0 mm (0.040 inch).

  1. Tighten bolts (10) to a torque of 1600 N·m (1180 lb ft).

  1. Repeat Steps 3 through 7 for the opposite machine side.

  1. Release the pressure in the hydraulic system. Refer to Disassembly and Assembly, "System Pressure - Release".



    Illustration 3g01901033

  1. Connect hose assemblies (8) .



    Illustration 4g01901019

  1. Attach a suitable lifting device to stabilizer link (4). The weight of stabilizer link (4) is approximately 80 kg (175 lb).

  1. Raise the end of stabilizer link (4) to the front trunnion.

  1. Install pin (7) ,retainer (6) and bolts (5) .



    Illustration 5g01901000

  1. Extend the lift cylinder rod to the trunnion.

  1. Insert an equal amount of shims in the spaces between the bearing cap and the lift cylinder, as needed.

  1. Install bolts (1) ,cap (2) and shims (3) .

  1. Tighten bolts (1) .

Information System:

834H Wheel Dozer and 836H Landfill Compactor Machine Systems Push Arms and Blade - Remove
C13 Engines for Caterpillar Built Machines Pressure Sensor (DPF) - Remove and Install - Differential Pressure, Clean Emissions Module
2009/06/29 New Hardware is Available for Certain Wheel Tractor-Scrapers Draft Frames {6204, 7000, 7960}
C15 and C18 Industrial Engines Nozzle Heater Harness - Remove and Install
C13 Engines for Caterpillar Built Machines Fuel Manifold (ARD) - Remove and Install - Clean Emissions Module
C13 Engines for Caterpillar Built Machines Air Control Valve - Remove and Install - ARD Combustion, Clean Emissions Module
Procedure to Align the Dial on the Fuel Sender{1273, 7481, 7857}
D7E Track-Type Tractor Power Train Track Roller Frame - Remove and Install
AccuGrade</SUP> GPS / Single UTS / Site and Laser Reference v11 for Excavators Universal Total Station - MT900
C13 Engines for Caterpillar Built Machines Combustion Head - Remove and Install - Clean Emissions Module
C13 Tier 4 Final Engines Electronic Control System Components
C15 and C18 Engines for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Assemble
D5R Track-Type Tractor Power Train Track Roller Frame
C13 Engines for Caterpillar Built Machines Flame Detection Temperature Sensor - Remove and Install - Clean Emissions Module
C13 Engines for Caterpillar Built Machines Diesel Particulate Filter - Remove and Install - Clean Emissions Module
D6T Track-Type Tractor Hydraulic System Pressure Taps
C13 Engines for Caterpillar Built Machines Catalyst - Remove and Install - Diesel Oxidation Catalyst, Clean Emissions Module
Installation and Removal of the V-PAT Bulldozer{6050, 6079}
C13 Engines for Caterpillar Built Machines Temperature Sensor (DPF) - Remove and Install - Clean Emissions Module
Oversized Injector Sleeves for Remanufactured Cylinder Heads On Medium Sized Engines{1100, 1101, 1125}
Installation of Ripper (3TP){6310}
2009/10/29 A New Bowl for the Fuel/Water Separator Is Used {1261, 1263}
Improved Method for Installing the Actual Gear Position Sensor {1439, 3061}
2009/05/04 Improved Installation Procedure for the Heater Cable {7304}