EPC Parts Catalogs

834H Wheel Dozer and 836H Landfill Compactor Machine Systems Push Arms and Blade - Remove Caterpillar


  1. Home
  2. Disassembly and Assembly
  3. #126782
Push Arms and Blade - Remove
`
834H Wheel Dozer and <BR> 836H Landfill Compactor Machine Systems [RENR6224]
834H Wheel Dozer and 836H Landfill Compactor Machine Systems Lift Cylinder - Remove and Install
834H Wheel Dozer and 836H Landfill Compactor Machine Systems Push Arms and Blade - Install
WORK TOOLS
BLADE GP
834H Wheel Dozer and 836H Landfill Compactor Machine Systems Push Arms and Blade - Remove
834H Wheel Dozer and 836H Landfill Compactor Machine Systems Push Arms and Blade - Install
1.1. Removal Procedure

Removal Procedure

Show/hide table
------ WARNING! ------

Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin.

----------------------

Show/hide table
NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "AVSpare Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on AVSpare products.

Dispose of all fluids according to local regulations and mandates.

Note: Put identification marks on all lines, on all hoses and on all wires for installation purposes. Plug all lines and all hoses. This will help to prevent fluid loss and this will help to keep contaminants from entering the system.

    Show/hide table

    Illustration 1g01901000

  1. Remove bolts (1), cap (2), and shims (3) from the lift cylinder rod. Note the quantity and the location of the shims for assembly purposes.

  1. Start the machine.

  1. Retract the lift cylinder rod.

  1. Stop the machine.
    Show/hide table

    Illustration 2g01901019

  1. Attach a suitable lifting device to stabilizer link (4). The weight of stabilizer link (4) is approximately 80 kg (175 lb).

  1. Remove bolts (5), retainer (6), and the pin (7) .

  1. Secure stabilizer link (4) to the machine. This will allow the machine to be moved.

  1. Release the pressure in the hydraulic system. Refer to Disassembly and Assembly, "System Pressure - Release".
    Show/hide table

    Illustration 3g01901033

  1. Disconnect hose assemblies (8).
    Show/hide table

    Illustration 4g01901054

  1. Position suitable blocking under push arm (9), as shown.

  1. Remove bolts (10), bearing cap (11), and the shims from push arm (9). Note the quantity and the location of the shims for assembly purposes.

  1. Repeat Steps 10 and 11 for the opposite side.
    Show/hide table

    Illustration 5g01901755

  1. Move the machine away from the push arm assembly (9) .

Information System:

C13 Engines for Caterpillar Built Machines Pressure Sensor (DPF) - Remove and Install - Differential Pressure, Clean Emissions Module
2009/06/29 New Hardware is Available for Certain Wheel Tractor-Scrapers Draft Frames {6204, 7000, 7960}
C15 and C18 Industrial Engines Nozzle Heater Harness - Remove and Install
C13 Engines for Caterpillar Built Machines Fuel Manifold (ARD) - Remove and Install - Clean Emissions Module
C13 Engines for Caterpillar Built Machines Air Control Valve - Remove and Install - ARD Combustion, Clean Emissions Module
Procedure to Align the Dial on the Fuel Sender{1273, 7481, 7857}
D7E Track-Type Tractor Power Train Track Roller Frame - Remove and Install
AccuGrade</SUP> GPS / Single UTS / Site and Laser Reference v11 for Excavators Universal Total Station - MT900
C13 Engines for Caterpillar Built Machines Combustion Head - Remove and Install - Clean Emissions Module
C13 Tier 4 Final Engines Electronic Control System Components
C15 and C18 Engines for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Assemble
2009/05/11 Improved Wiring Harnesses Are Now Available {1408}
834H Wheel Dozer and 836H Landfill Compactor Machine Systems Push Arms and Blade - Install
D5R Track-Type Tractor Power Train Track Roller Frame
C13 Engines for Caterpillar Built Machines Flame Detection Temperature Sensor - Remove and Install - Clean Emissions Module
C13 Engines for Caterpillar Built Machines Diesel Particulate Filter - Remove and Install - Clean Emissions Module
D6T Track-Type Tractor Hydraulic System Pressure Taps
C13 Engines for Caterpillar Built Machines Catalyst - Remove and Install - Diesel Oxidation Catalyst, Clean Emissions Module
Installation and Removal of the V-PAT Bulldozer{6050, 6079}
C13 Engines for Caterpillar Built Machines Temperature Sensor (DPF) - Remove and Install - Clean Emissions Module
Oversized Injector Sleeves for Remanufactured Cylinder Heads On Medium Sized Engines{1100, 1101, 1125}
Installation of Ripper (3TP){6310}
2009/10/29 A New Bowl for the Fuel/Water Separator Is Used {1261, 1263}
Improved Method for Installing the Actual Gear Position Sensor {1439, 3061}