Valve Mechanism Cover - Remove and Install - C32
`
C27 and C32 Engines for Caterpillar Built Machines
[RENR9217]
C27 and C32 Engines for Caterpillar Built Machines
Vibration Damper and Pulley - Remove and Install - Type 2
C27 and C32 Engines for Caterpillar Built Machines
Exhaust Manifold - Remove and Install
BASIC ENGINE
VALVE MECHANISM GP
C27 and C32 Generator Set Engines
Valve Mechanism Cover Base - Remove and Install
C27 and C32 Generator Set Engines
Rocker Arm and Shaft - Remove
C27 and C32 Generator Set Engines
Rocker Arm and Shaft - Install
C27 and C32 Engines for Caterpillar Built Machines
Valve Mechanism Cover - Remove and Install - C27
C27 and C32 Engines for Caterpillar Built Machines
Valve Actuator (Variable) - Remove
C27 and C32 Engines for Caterpillar Built Machines
Valve Actuator (Variable) - Install
C27 and C32 Engines for Caterpillar Built Machines
Valve Mechanism Cover - Remove and Install - C32
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove bolts (1), valve mechanism covers (2) and the seals.
Show/hide table
![]() | |
Illustration 1 | g01147941 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install seals (3) into valve mechanism covers (2).
Show/hide table
Illustration 4 g01147941 Show/hide tableIllustration 5 g03225827 - Position valve mechanism covers (2) on the valve mechanism cover base. Install bolts (1). Tighten bolts (1) in the sequence shown in illustration 5.
Show/hide table
![]() | |
Illustration 2 | g06078165 |
Show/hide table
![]() | |
Illustration 3 | g06078161 |
Note: Be sure that the seal is seated correctly into the valve mechanism cover. The narrow side of the seal should face out away from the valve mechanism cover.
Information System:
C9.3 Engines for Caterpillar Built Machines
Electrical Connectors - Inspect
D5R Track-Type Tractor Hydraulic System
Steering - Calibrate
2009/05/04
A Repair Kit for the Magnet is Now Available for the AccuGrade CD700 Display {7490}
C13 Tier 4 Final Engines
Lubrication System
A New Flange Assembly For the Torque Converter On the D10T Is Now Used{3101}
C15 and C18 Industrial Engines
Flame Detection Temperature Sensor - Remove and Install - Clean Emissions Module
Installation of VIMS Guardian on Underground Mining Machines{7601}
2009/04/27
Preferred Positions for Mechanically Attached Wear Plates (MAWPS) {6100, 6120, 6820}
2009/07/27
A New Fuel Line Is Now Used on D9T Track-Type Tractors {1274}
Relocation of the Rear Disconnect Switch {1411}
3500B and 3500C Marine Engines
Alternator and Regulator
2009/04/27
Proper Long Term Storage of Caterpillar Products {0355, 1000, 7000}
C9.3 Engines for Caterpillar Built Machines
ECM Software - Install
C13 Tier 4 Final Engines
General Information - C13 Engines
C9.3 Engines for Caterpillar Built Machines
Injector Trim File - Install
Field Installation of the Payload Monitor Gp Kits{7494}
Relocation Of The Expansion Tanks For The Implement Hydraulic System{1354, 5057, 5505}
2009/06/01
A New Bracket Updates the Access Door Group {7251, 7273}
C15 and C18 Industrial Engines
Air Inlet Elbow - Remove and Install
2009/05/11
Improved Wiring Harnesses Are Now Available {1408}
C15 and C18 Engines for Caterpillar Built Machines
Exhaust Gas Valve (NRS) - Assemble
C13 Tier 4 Final Engines
Electronic Control System Components
C13 Engines for Caterpillar Built Machines
Combustion Head - Remove and Install - Clean Emissions Module
AccuGrade</SUP> GPS / Single UTS / Site and Laser Reference v11 for Excavators
Universal Total Station - MT900