D3G, D4G and D5G Track-Type Tractors Electrohydraulic Diagnostic Code List Caterpillar


Diagnostic Code List
`
D3G, D4G and D5G Track-Type Tractors Electrohydraulic [RENR7313]
ELECTRICAL AND STARTING SYSTEM
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Diagnostic Code List

Use the AVSpare Electronic Technician in order to determine the diagnostic codes for the ECM. After determining the diagnostic codes, refer to the corresponding test procedure for more information. Perform the procedure that corresponds to the diagnostic code (CID and FMI). The following table is a list of possible diagnostic codes for the ECM.

Table 1
Diagnostic Codes For Machine ECM (MID No. 079) (1)    
For troubleshooting, see the procedure with the same CID And FMI No.    
CID / FMI     Description    
CID 0017 Solenoid Valve (Fuel Shutoff)    
FMI 03     Voltage above normal or shorted high.    
FMI 05     Current below normal or open circuit.    
FMI 06     Current above normal or grounded circuit.    
CID 0041 Sensor Power Supply (8 DCV)    
FMI 00     Data Valid but above normal operating range.    
CID 0070 Rocker Switch (Parking Brake)    
FMI 02     Data erratic, intermittent, or incorrect.    
FMI 01     Data Valid but below normal operating range.    
CID 0110 Temperature Sensor (Engine Coolant)    
FMI 03     Voltage above normal or shorted high.    
CID 0133 Solenoid Valve (Transmission Pilot Pressure)    
FMI 03     Voltage above normal or shorted high.    
FMI 05     Current below normal or open circuit.    
FMI 06     Current above normal or grounded circuit.    
CID 0153 Speed Sensor (Right Track)    
FMI 08     Abnormal frequency, pulse width, or period.    
CID 0154 Speed Sensor (Left Track)    
FMI 08     Abnormal frequency, pulse width, or period.    
CID 0168 Electrical System    
FMI 03     Voltage above normal or shorted high.    
FMI 04     Voltage below normal or shorted low.    
CID 0190 Engine Speed Sensor    
FMI 08     Abnormal frequency, pulse width or period.    
CID 0444 Magnetic Switch (Start Relay)    
FMI 03     Voltage above normal or shorted high.    
FMI 05     Current below normal or open circuit.    
FMI 06     Current above normal or grounded circuit.    
CID 0468 Position Sensor (Service Brake Pedal)    
FMI 03     Voltage above normal or shorted high.    
FMI 04     Voltage below normal or shorted low.    
FMI 08     Abnormal frequency, pulse width or period.    
CID 0617 Relay (Inlet Air Heater)    
FMI 03     Voltage above normal or shorted high.    
FMI 05     Current below normal or open circuit.    
FMI 06     Current above normal or grounded circuit.    
FMI 13     Out of calibration.    
CID 0650 Harness Code    
FMI 12     Bad device or component failed.    
CID 0681 Solenoid Valve (Parking Brake)    
FMI 03     Voltage above normal or shorted high.    
FMI 06     Current above normal or grounded circuit.    
FMI 05     Current below normal or open circuit.    
CID 0817 ECM Internal Backup Battery    
FMI 04     Voltage below normal or shorted low.    
CID 1482 Sensor Power Supply (10 DCV)    
FMI 00     Data Valid but above normal operating range.    
FMI 01     Data Valid but below normal operating range.    
CID 1693 Position Sensor (Deceleration Pedal)    
FMI 03     Voltage above normal or shorted high.    
FMI 04     Voltage below normal or shorted low.    
FMI 08     Abnormal frequency, pulse width or period.    
FMI 13     Out of calibration.    
CID 1699 Position Sensor (Forward/Neutral/Reverse)    
FMI 03     Voltage above normal or shorted high.    
FMI 04     Voltage below normal or shorted low.    
FMI 08     Abnormal frequency, pulse width or period.    
FMI 13     Out of calibration.    
CID 1700 Position Sensor (Joystick)    
FMI 03     Voltage above normal or shorted high.    
FMI 04     Voltage below normal or shorted low.    
FMI 08     Abnormal frequency, pulse width or period.    
FMI 13     Out of calibration.    
CID 1701 Switch (Machine Acceleration)    
FMI 02     Data erratic, intermittent, or incorrect.    
CID 1702 Switch (Machine Deceleration)    
FMI 02     Data erratic, intermittent, or incorrect.    
CID 1703 Proportional Solenoid Valve (Forward Left Drive Pump)    
FMI 03     Voltage above normal or shorted high.    
FMI 05     Voltage below normal or shorted low.    
FMI 06     Failure mode not identifiable.    
CID 1704 Proportional Solenoid Valve (Reverse Left Drive Pump)    
FMI 03     Voltage above normal or shorted high.    
FMI 05     Voltage below normal or shorted low.    
FMI 06     Failure mode not identifiable.    
CID 1705 Proportional Solenoid Valve (Forward Right Drive Pump)    
FMI 03     Voltage above normal or shorted high.    
FMI 05     Voltage below normal or shorted low.    
FMI 06     Failure mode not identifiable.    
CID 1706 Proportional Solenoid Valve (Reverse Right Drive Pump)    
FMI 03     Voltage above normal or shorted high.    
FMI 05     Voltage below normal or shorted low.    
FMI 06     Failure mode not identifiable.    
CID 1707 Proportional Solenoid Valve (Left Drive Motor)    
FMI 03     Voltage above normal or shorted high.    
FMI 05     Voltage below normal or shorted low.    
FMI 06     Failure mode not identifiable.    
CID 1708 Proportional Solenoid Valve (Right Drive Pump)    
FMI 03     Voltage above normal or shorted high.    
FMI 06     Failure mode not identifiable.    
FMI 05     Voltage below normal or shorted low.    
CID 1960 ECM Cannot Communicate With the Electronic Key Reader    
FMI 09     Abnormal Update.    
( 1 ) For the Machine ECM, the MID is 079. This table pertains only to diagnostic codes with a MID of 079.

Information System:

2003/06/02 New Guard Assembly for the Tilt Position Sensor Is Used {5736}
613C Series II Wheel Tractor Power Train Torque Converter - Assemble
3044C Industrial Engine and Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
613C Series II Wheel Tractor Power Train Torque Converter - Disassemble
3044C Industrial Engine and Engines for Caterpillar Built Machines Water Pump - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
613C Series II Wheel Tractor Power Train Torque Converter - Install
2003/05/19 Correction to Testing and Adjusting , "Ride Control Accumulator Recharging Procedure" {5077}
2003/05/12 Correction to Testing and Adjusting , "Transmission Pressures - Test and Adjust" {3081}
613C Series II Wheel Tractor Power Train Torque Converter - Remove
980G Series II Wheel Loader Power Train Transmission Pressures - Test and Adjust
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install
854G Wheel Tractor and 992G Wheel Loader Power Train Axle Shaft - Remove and Install
980G Series II Wheel Loader Cooling System Coolant Sample (Level 1) - Obtain
3044C Industrial Engine and Engines for Caterpillar Built Machines Fuel Injection Lines - Remove and Install - Turbocharged Engines
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Oil Cooler - Remove
854G Wheel Tractor and 992G Wheel Loader Power Train Transmission Hydraulic Control Valve - Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Oil Cooler - Install
AD30 Underground Articulated Truck Machine Electrical System Brake Oil Temperature
966G II and 972G II Wheel Loaders Monitoring System
854G Wheel Tractor and 992G Wheel Loader Power Train Transmission Hydraulic Control Valve - Remove
TH220B, TH330B and TH340B Telehandlers Machine Systems Carriage Cylinder (Sideshift)
3044C Industrial Engine and Engines for Caterpillar Built Machines Turbocharger - Remove
854G Wheel Tractor and 992G Wheel Loader Power Train Final Drive and Wheel - Disassemble