953C, 963C and 973C Track-Type Loaders Transmission Electronic Control System MID 079 - CID 0132 - FMI 08 Caterpillar


MID 079 - CID 0132 - FMI 08
`
MID 079 CID 0132 FMI 08

Conditions Which Generate This Code:



Illustration 1g01003457
Schematic of the Pressure Sensor (Override)

This diagnostic code is associated with the pressure sensor (override). The FMI 08 means that the ECM has determined that the signal frequency or the signal pulse width is not within the expected range.

The output frequency of the pressure sensor is approximately 500 hertz. The duty cycle of the signal increases as the pressure of the oil increases and the duty cycle decreases as the pressure decreases. The range of the duty cycle is from 10% to 94 %.

The possible causes of this diagnostic code are listed below:

  • The sensor has failed.

  • Intermittent connections or poor connections

  • Mechanical devices are loose.

  • The ECM has failed. This is unlikely.

Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0132 FMI 08 is active before performing this procedure.

Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.

Test Step 1. CHECK FOR POWER AT THE SENSOR.

  1. Do not disconnect the harness connector from the sensor.

  2. Turn the key start switch and the disconnect switch to the ON position.

  3. At the back of the harness connector for the sensor, insert a 7X-1710 Multimeter Probe along the voltage supply wire (contact A).

  4. Measure the voltage from contact A to frame ground.

Expected Result:

The voltage is 8 DCV.

Results:

  • OK - The voltage is 8 DCV. Proceed to Test Step 3.

  • NOT OK - The voltage is NOT 8 DCV. The circuit is open.

    Repair: Repair the machine harness or replace the machine harness.

    STOP

Test Step 2. CHECK THE SIGNAL CIRCUIT OF THE SENSOR.

  1. Turn the key start switch and the disconnect switch to the OFF position.

  2. At the back of the harness connector for the sensor, remove the 7X-1710 Multimeter Probe from contact A and insert the probe along the signal wire (contact C).

  3. At the back of the harness connector for the sensor, insert the 7X-1710 Multimeter Probe along the ground wire (contact B).

  4. Turn the disconnect switch and the key start switch to the ON position.

  5. Monitor the signal of the sensor with the 146-4080 Digital Multimeter.

  6. Without disconnecting the sensor or the hardware that is associated with the sensor from the machine, take the sensor through the full operating range of the sensor.

    Note: On some machines, it may be necessary to start the engine in order to take the sensor through the full operating range of the sensor.

Expected Result:

The sensor's signal responds in the manner that is described at the begining of this procedure.

Results:

  • OK - The sensor's signal responds correctly. The sensor is operating correctly. Proceed to Test Step 3.

  • NOT OK - The sensor's signal does not respond correctly. The sensor is NOT operating correctly.

    Repair: Replace the sensor.

    STOP

Test Step 3. CHECK THE SIGNAL CIRCUIT AT THE ECM.

  1. Turn the key start switch and the disconnect switch to the OFF position.

  2. Insert the 7X-1710 Multimeter Probes into the back of the ECM connector along B-29 (wire 852-GN(Green)) and D-15 (wire G939-PK(Pink)).

  3. Turn the disconnect switch and the key start switch to the ON position.

  4. Monitor the signal of the sensor with the 146-4080 Digital Multimeter.

  5. Without disconnecting the sensor or the hardware that is associated with the sensor from the machine, take the sensor through the full operating range of the sensor.

    Note: On some machines, it may be necessary to start the engine in order to take the sensor through the full operating range of the sensor.

Expected Result:

The sensor's signal responds in the manner that is described at the begining of this procedure.

Results:

  • OK - The sensor's signal responds correctly. The sensor is operating correctly. Proceed to Test Step 4.

  • NOT OK - The sensor's signal does not respond correctly. The harness has failed.

    Repair: Repair the machine harness or replace the machine harness.

    STOP

Test Step 4. CHECK THE SIGNAL CIRCUIT FOR A SHORT IN THE HARNESS.

  1. The key start switch and the disconnect switch remain in the OFF position.

  2. Disconnect the machine harness connectors from the sensor and the ECM.

  3. Measure the resistance between contact B-29 (wire 852-GN(Green)) and all contacts that are used in the machine harness connectors for the ECM.

Expected Result:

The resistance is greater than 5000 ohms.

Results:

  • OK - The resistance is greater than 5000 ohms. The circuit is correct. Proceed to Test Step 5.

  • NOT OK - The resistance is less than 5 ohms. The signal circuit is shorted to another circuit in the harness.

    Repair: Repair the machine harness or replace the machine harness.

    STOP

Test Step 5. CHECK IF THE DIAGNOSTIC CODE REMAINS

  1. Inspect the harness connectors and clean the contacts of the machine harness connectors.

  2. Reconnect all harness connectors.

  3. Turn the disconnect switch and the key start switch to the ON position.

  4. Operate the machine.

  5. Check the status of the CID 0132 FMI 08.

Expected Result:

The CID 0132 FMI 08 is not active.

Results:

  • OK - The CID 0132 FMI 08 is not active. The diagnostic code does not exist at this time. The initial diagnostic code was probably caused by a poor connection or a short at one of the connectors that was disconnected and reconnected. Resume normal operation.

    STOP

  • NOT OK - The CID 0132 FMI 08 is active. The diagnostic code has not been corrected. The ECM may have failed.

    Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the failure is not found, replace the ECM. See the Testing and Adjusting , "Electronic Control Module (ECM)- Replace".

    STOP

Information System:

615C Series II Wheel Tractor-Scraper Wheel Tractor Power Train Axle Housing - Remove
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Power Train Transmission and Torque Converter - Install
963C Track-Type Loader Monitoring System
963C Track-Type Loader Towing the Machine
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Operator Controls - Steering Control Console
2003/06/01 SOLAS Requirement for Screening Fuel and Oil Line Connections on Marine Engines {1274, 1307}
Installation Instructions for the 2Q-8245 Fan Control Ar (Auto Reversing) (Kit){1386, 138R}
2003/06/09 A New Fuse Panel Is Used {1417}
TH220B, TH330B and TH340B Telehandlers Hydraulic System Location of Hydraulic Components
980G Series II Wheel Loader Monitoring System
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Power Train Transmission and Torque Converter - Remove
IT28G Integrated Toolcarrier and 924G, 924Gz and 928G Wheel Loaders Window Wiper and Wiper Motor
990 Series II Wheel Loader Hydraulic System Ride Control Accumulator - Test and Charge
615C Series II Wheel Tractor-Scraper Wheel Tractor Power Train Axle Housing - Install
953C Track-Type Loader Power Train Hydraulic Oil Filter
953C Track-Type Loader Power Train Hydrostatic Drive Pump
953C Track-Type Loader Power Train Brake and Final Drive Group
AD30 Underground Articulated Truck Machine Electrical System Charging System
AD30 Underground Articulated Truck Machine Electrical System Accessories
AD30 Underground Articulated Truck Machine Electrical System Battery Disconnect Switch
AD30 Underground Articulated Truck Machine Electrical System Electrical Power Supply
2003/05/19 Correction to Testing and Adjusting , "Ride Control Accumulator - Test and Charge" {5077}
953C Track-Type Loader Power Train Electronic Control Module Manifold
615C Series II Wheel Tractor-Scraper Wheel Tractor Power Train Axle Shaft - Remove