D7 Track-Type Tractor Electrohydraulic Systems Diagnostic Trouble Codes Caterpillar

Diagnostic Trouble Codes

D7 Track-Type Tractor Electrohydraulic Systems [M0120325]

D7 Track-Type Tractor Electrohydraulic Systems Connector Contact Description

D7 Track-Type Tractor Electrohydraulic Systems Symptom Troubleshooting

ELECTRICAL AND STARTING SYSTEM

826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Diagnostic Capabilities

D7 Track-Type Tractor Electrohydraulic Systems Determining Diagnostic Trouble Codes

D7 Track-Type Tractor Electrohydraulic Systems Event Codes

D7 Track-Type Tractor Electrohydraulic Systems Diagnostic Trouble Codes

1.1. Diagnostic Trouble Code (DTC) List

2.2. Implement ECM

3.2. Machine ECM

The following is a list of Diagnostic Trouble Codes (DTCs). When a diagnostic code becomes active, refer to the Troubleshooting section of this manual for a specific troubleshooting procedure.

Portions of this material are reprinted with permission from SAE J1939DA_201607© 2016 SAE International. SAE International is not responsible for any use or translation of this material, in whole or in part. Contact SAE International to obtain a complete copy of SAE J1939DA_201607, the official definitive source of this standard.

Diagnostic Trouble Code (DTC) List

Each DTC is made up of two numbers. The first number is the Component Identifier (CID). The second number is the Failure Mode Identifier (FMI).

The Module Identifier (MID) identifies the ECM associated with the DTC. For example, MID 082 identifies the Implement ECM.

Implement ECM

Show/hide table

Table 1
Diagnostic Trouble Codes for the Implement ECM (MID 082)
DTC	Description	Test Procedure
41-3	8 VDC Supply: Voltage Above Normal	Sensor Supply - Test
41-4	8 VDC Supply: Voltage Below Normal	Sensor Supply - Test
96-3	Fuel Level Sensor: Voltage Above Normal	Sensor Signal (Analog Active) - Test
96-4	Fuel Level Sensor: Voltage Below Normal	Sensor Signal (Analog Active) - Test
246-9	Proprietary CAN Data Link: Abnormal Update Rate	CAN Data Link - Test
246-14	Proprietary CAN Data Link: Special Instruction	CAN Data Link - Test
247-9	SAE J1939 Data Link: Abnormal Update Rate	CAN Data Link - Test
247-14	SAE J1939 Data Link: Special Instruction	CAN Data Link - Test
262-3	5 VDC Sensor Power Supply: Voltage Above Normal	Sensor Supply - Test
262-4	5 VDC Sensor Power Supply: Voltage Below Normal	Sensor Supply - Test
296-9	Transmission Control: Abnormal Update Rate	CAN Data Link - Test
296-14	Transmission Control: Special Instruction	CAN Data Link - Test
490-3	Implement Lockout Switch: Voltage Above Normal	Operator Control Switch (Switch to Ground) - Test
490-4	Implement Lockout Switch: Voltage Below Normal	Operator Control Switch (Switch to Ground) - Test
497-3	Tilt Right Solenoid: Voltage Above Normal	Solenoid Valve - Test
497-5	Tilt Right Solenoid: Current Below Normal	Solenoid Valve - Test
497-6	Tilt Right Solenoid: Current Above Normal	Solenoid Valve - Test
497-13	Tilt Right Solenoid: Out of Calibration	Solenoid Valve - Test
498-3	Tilt Left Solenoid: Voltage Above Normal	Solenoid Valve - Test
498-5	Tilt Left Solenoid: Current Below Normal	Solenoid Valve - Test
498-6	Tilt Left Solenoid: Current Above Normal	Solenoid Valve - Test
498-13	Tilt Left Solenoid: Out of Calibration	Solenoid Valve - Test
588-9	Monitoring System Display: Abnormal Update Rate	CAN Data Link - Test
588-14	Monitoring System Display: Special Instruction	CAN Data Link - Test
590-9	Engine Control Module: Abnormal Update	CAN Data Link - Test
590-14	Engine Control Module: Special Instruction	CAN Data Link - Test
600-3	Hydraulic Oil Temperature Sensor: Voltage Above Normal	Sensor Signal (Analog, Passive) - Test
600-4	Hydraulic Oil Temperature Sensor: Voltage Below Normal	Sensor Signal (Analog, Passive) - Test
779-3	Cab Air Temperature Sensor: Voltage Above Normal:	Sensor Signal (Analog, Passive) - Test
779-4	Cab Air Temperature Sensor: Voltage Below Normal	Sensor Signal (Analog, Passive) - Test
874-3	Mode Select Switch: Voltage Above Normal	Operator Control Switch (Switch To Ground) - Test
874-4	Mode Select Switch: Voltage Below Normal	Operator Control Switch (Switch To Ground) - Test
875-3	Manual Select Switch: Voltage Above Normal	Operator Control Switch (Switch To Ground) - Test
875-4	Manual Select Switch: Voltage Below Normal	Operator Control Switch (Switch To Ground) - Test
879-2	Ripper Shank In/Out Lever Position Sensor: Erratic, Intermittent, or Incorrect	Sensor Signal (PWM) - Test
879-3	Ripper Shank In/Out Lever Position Sensor: Voltage Above Normal	Sensor Signal (PWM) - Test
879-4	Ripper Shank In/Out Lever Position Sensor: Voltage Below Normal	Sensor Signal (PWM) - Test
879-8	Ripper Shank In/Out Lever Position Sensor: Abnormal Frequency, Pulse Width, or Period	Sensor Signal (PWM) - Test
879-13	Ripper Shank In/Out Lever Position Sensor: Out of Calibration	Sensor Signal (PWM) - Test
880-2	Ripper Raise/Lower Lever Position Sensor: Data Erratic, Intermittent, or Incorrect	Sensor Signal (PWM) - Test
880-3	Ripper Raise/Lower Lever Position Sensor: Voltage Above Normal	Sensor Signal (PWM) - Test
880-4	Ripper Raise/Lower Lever Position Sensor: Voltage Below Normal	Sensor Signal (PWM) - Test
880-8	Ripper Raise/Lower Lever Position Sensor: Abnormal Frequency, Pulse Width, or Period	Sensor Signal (PWM) - Test
880-13	Ripper Raise/Lower Lever Position Sensor: Out of Calibration	Sensor Signal (PWM) - Test
882-3	Implement Lockout Solenoid (Switched): Voltage Above Normal	Solenoid Valve (Switch Controlled) - Test
882-5	Implement Lockout Solenoid (Switched): Current Below Normal	Solenoid Valve (Switch Controlled) - Test
882-6	Implement Lockout Solenoid (Switched): Current Above Normal	Solenoid Valve (Switch Controlled) - Test
886-3	Ripper Shank In Solenoid: Voltage Above Normal	Solenoid Valve - Test
886-5	Ripper Shank In Solenoid: Current Below Normal	Solenoid Valve - Test
886-6	Ripper Shank In Solenoid: Current Above Normal	Solenoid Valve - Test
886-13	Ripper Shank In Solenoid: Out of Calibration	Solenoid Valve - Test
887-3	Ripper Shank Out Solenoid: Voltage Above Normal	Solenoid Valve - Test
887-5	Ripper Shank Out Solenoid: Current Below Normal	Solenoid Valve - Test
887-6	Ripper Shank Out Solenoid: Current Above Normal	Solenoid Valve - Test
887-13	Ripper Shank Out Solenoid: Out of Calibration	Solenoid Valve - Test
888-3	Ripper Shank Lower Solenoid: Voltage Above Normal	Solenoid Valve - Test
888-5	Ripper Shank Lower Solenoid: Current Below Normal	Solenoid Valve - Test
888-6	Ripper Shank Lower Solenoid: Current Above Normal	Solenoid Valve - Test
888-13	Ripper Shank Lower Solenoid: Out of Calibration	Solenoid Valve - Test
889-3	Ripper Shank Raise Solenoid: Voltage Above Normal	Solenoid Valve - Test
889-5	Ripper Shank Raise Solenoid: Current Below Normal	Solenoid Valve - Test
889-6	Ripper Shank Raise Solenoid: Current Above Normal	Solenoid Valve - Test
889-13	Ripper Shank Raise Solenoid: Out of Calibration	Solenoid Valve - Test
967-9	Machine Application: Abnormal Update	CAN Data Link - Test
1035-9	GPS Receiver: Abnormal Update Rate	Sensor (Data Link Type) - Test
1078-2	Blade Control Handle Lift Position Sensor: Data Erratic, Intermittent, or Incorrect	Sensor Signal (PWM) - Test
1078-3	Blade Control Handle Lift Position Sensor: Voltage Above Normal	Sensor Signal (PWM) - Test
1078-4	Blade Control Handle Lift Position Sensor: Voltage Below Normal	Sensor Signal (PWM) - Test
1078-8	Blade Control Handle Lift Position Sensor: Abnormal Frequency, Pulse Width, or Period	Sensor Signal (PWM) - Test
1079-2	Blade Control Handle Tilt Position Sensor: Data Erratic, Intermittent, or Incorrect	Sensor Signal (PWM) - Test
1079-3	Blade Control Handle Tilt Position Sensor: Voltage Above Normal	Sensor Signal (PWM) - Test
1079-4	Blade Control Handle Tilt Position Sensor: Voltage Below Normal	Sensor Signal (PWM) - Test
1079-8	Blade Control Handle Tilt Position Sensor: Abnormal Frequency, Pulse Width, or Period	Sensor Signal (PWM) - Test
1197-3	Blade Lower Solenoid: Voltage Above Normal	Solenoid Valve - Test
1197-5	Blade Lower Solenoid: Current Below Normal	Solenoid Valve - Test
1197-6	Blade Lower Solenoid: Current Above Normal	Solenoid Valve - Test
1197-13	Blade Lower Solenoid: Out of Calibration	Solenoid Valve - Test
1198-3	Blade Raise Solenoid: Voltage Above Normal	Solenoid Valve - Test
1198-5	Blade Raise Solenoid: Current Below Normal	Solenoid Valve - Test
1198-6	Blade Raise Solenoid: Current Above Normal	Solenoid Valve - Test
1198-13	Blade Raise Solenoid: Out of Calibration	Solenoid Valve - Test
1326-2	ECM Location Code: Data Erratic, Intermittent, or Incorrect	ECM Location Code - Test
1393-4	Output Driver Enable Line: Voltage Below Normal	Sensor Supply - Test
1435-9	System Master Control Module: Abnormal Update Rate	CAN Data Link - Test
1435-14	System Master Control Module: Special Instruction	CAN Data Link - Test
1450-2	Main Hydraulic Pump Oil Pressure Sensor: Data Erratic, Intermittent, or Incorrect	Sensor Signal (Analog, Active) - Test
1450-3	Main Hydraulic Pump Oil Pressure Sensor: Voltage Above Normal	Sensor Signal (Analog, Active) - Test
1450-4	Main Hydraulic Pump Oil Pressure Sensor: Voltage Below Normal	Sensor Signal (Analog, Active) - Test
1450-8	Main Hydraulic Pump Oil Pressure Sensor: Abnormal Frequency, Pulse Width, or Period	Sensor Signal (Analog, Active) - Test
1482-3	10 VDC Sensor Power Supply: Voltage Above Normal	Sensor Supply - Test
1482-4	10 VDC Sensor Power Supply: Voltage Below Normal	Sensor Supply - Test
1603-9	Machine Control Module: Abnormal Update Rate	CAN Data Link - Test
1603-14	Machine Control Module: Special Instruction	CAN Data Link - Test
1677-4	Solenoid Return #4: Voltage Below Normal	Solenoid Return - Test
1677-5	Solenoid Return #4: Current Below Normal	Solenoid Return - Test
1678-4	Solenoid Return #5: Voltage Below Normal	Solenoid Return - Test
1678-5	Solenoid Return #5: Current Below Normal	Solenoid Return - Test
1871-3	Blade Quick Drop Solenoid: Voltage Above Normal	Solenoid Valve - Test
1871-5	Blade Quick Drop Solenoid: Current Below Normal	Solenoid Valve - Test
1871-6	Blade Quick Drop Solenoid: Current Above Normal	Solenoid Valve - Test
1874-3	Winch Lockout Switch: Voltage Above Normal	Operator Control Switch (Switch To Ground) - Test
1874-4	Winch Lockout Switch: Voltage Below Normal	Operator Control Switch (Switch To Ground) - Test
1881-2	Winch Control Handle Spool In/Out Position Sensor: Data Erratic, Intermittent, or Incorrect	Sensor Signal (PWM) - Test
1881-3	Winch Control Handle Spool In/Out Position Sensor: Voltage Above Normal	Sensor Signal (PWM) - Test
1881-4	Winch Control Handle Spool In/Out Position Sensor: Voltage Below Normal	Sensor Signal (PWM) - Test
1881-8	Winch Control Handle Spool In/Out Position Sensor: Abnormal Frequency, Pulse Width, or Period	Sensor Signal (PWM) - Test
1881-13	Winch Control Handle Spool In/Out Position Sensor: Out of Calibration	Sensor Signal (PWM) - Test
1883-3	Winch Low Speed Lock Switch: Voltage Above Normal	Operator Control Switch (Switch to Ground) - Test
1883-4	Winch Low Speed Lock Switch: Voltage Below Normal	Operator Control Switch (Switch to Ground) - Test
1884-3	Winch Spool In Solenoid: Voltage Above Normal	Solenoid Valve - Test
1884-5	Winch Spool In Solenoid: Current Below Normal	Solenoid Valve - Test
1884-6	Winch Spool In Solenoid: Current Above Normal	Solenoid Valve - Test
1884-13	Winch Spool In Solenoid: Out of Calibration	Solenoid Valve - Test
1885-3	Winch Spool Out Solenoid: Voltage Above Normal	Solenoid Valve - Test
1885-5	Winch Spool Out Solenoid: Current Below Normal	Solenoid Valve - Test
1885-6	Winch Spool Out Solenoid: Current Above Normal	Solenoid Valve - Test
1885-13	Winch Spool Out Solenoid: Out of Calibration	Solenoid Valve - Test
1887-3	Winch Low Speed Lock Solenoid: Voltage Above Normal	Solenoid Valve - Test
1887-5	Winch Low Speed Lock Solenoid: Current Below Normal	Solenoid Valve - Test
1887-6	Winch Low Speed Lock Solenoid: Current Above Normal	Solenoid Valve - Test
1945-9	Left GPS Receiver: Abnormal Update Rate	Sensor (Data Link Type) - Test
1946-9	Right GPS Receiver: Abnormal Update Rate	Sensor (Data Link Type) - Test
1952-2	Chassis Angle Sensor: Data Erratic, Intermittent, or Incorrect	Sensor (Data Link Type) - Test
1952-9	Chassis Angle Sensor: Abnormal Update Rate	Sensor (Data Link Type) - Test
1952-13	Chassis Angle Sensor: Out of Calibration	Sensor (Data Link Type) - Test
2110-2	Machine Pitch Sensor: Data Erratic, Intermittent or Incorrect	CAN Data Link - Test
2110-9	Machine Pitch Sensor: Abnormal Update Rate	CAN Data Link - Test
2110-13	Machine Pitch Sensor: Out of Calibration	CAN Data Link - Test
2110-14	Machine Pitch Sensor: Special Instruction	CAN Data Link - Test
2114-3	Blade Control Handle Trigger Switch: Voltage Above Normal	Operator Control Switch (Switch To Ground) - Test
2114-4	Blade Control Handle Trigger Switch: Voltage Below Normal	Operator Control Switch (Switch To Ground) - Test
2348-9	SAE J1939 Data Link #2: Abnormal Update Rate	CAN Data Link - Test
2348-14	SAE J1939 Data Link #2: Special Instruction	CAN Data Link - Test
2357-3	Air Conditioner Evaporator Coil Temperature Sensor: Voltage Above Normal	Sensor Signal (Analog, Passive) - Test
2357-4	Air Conditioner Evaporator Coil Temperature Sensor: Voltage Below Normal	Sensor Signal (Analog, Passive) - Test
2440-3	Winch Brake Solenoid: Voltage Above Normal	Solenoid Valve - Test
2440-5	Winch Brake Solenoid: Current Below Normal	Solenoid Valve - Test
2440-6	Winch Brake Solenoid: Current Above Normal	Solenoid Valve - Test
2661-3	Cab Air Temperature Dial: Voltage Above Normal	Switch Circuits - Test
2661-4	Cab Air Temperature Dial: Voltage Below Normal	Switch Circuits - Test
2663-3	Cab Ventilation Duct Temperature Sensor: Voltage Above Normal	Sensor Signal (Analog, Passive) - Test
2663-4	Cab Ventilation Duct Temperature Sensor: Voltage Below Normal	Sensor Signal (Analog, Passive) - Test
2671-3	Air Conditioner Compressor Clutch Solenoid: Voltage Above Normal	Solenoid Valve - Test
2671-5	Air Conditioner Compressor Clutch Solenoid: Current Below Normal	Solenoid Valve - Test
2671-6	Air Conditioner Compressor Clutch Solenoid: Current Above Normal	Solenoid Valve - Test
2811-3	Cab Blower Speed Control: Voltage Above Normal	Switch Circuits - Test
2811-4	Cab Blower Speed Control: Voltage Below Normal	Switch Circuits - Test
3044-3	Main Hydraulic Pump Load Sense Reduction Solenoid: Voltage Above Normal	Solenoid Valve - Test
3044-5	Main Hydraulic Pump Load Sense Reduction Solenoid: Current Below Normal	Solenoid Valve - Test
3044-6	Main Hydraulic Pump Load Sense Reduction Solenoid: Current Above Normal	Solenoid Valve - Test
3210-3	Transmission Pump Bypass Solenoid: Voltage Above Normal	Solenoid Valve - Test
3210-5	Transmission Pump Bypass Solenoid: Current Below Normal	Solenoid Valve - Test
3210-6	Transmission Pump Bypass Solenoid: Current Above Normal	Solenoid Valve - Test
3423-9	Grade Control System: Abnormal Update Rate	Sensor (Data Link Type) - Test
3423-13	Grade Control System: Out of Calibration	Sensor (Data Link Type) - Test
3423-14	Grade Control System: Special Instruction	Sensor (Data Link Type) - Test
3601-3	Automatic Ripper Control Switch: Voltage Above Normal	Operator Control Switch (Switch to Ground) - Test
3601-4	Automatic Ripper Control Switch: Voltage Below Normal	Operator Control Switch (Switch to Ground) - Test
3744-2	Winch Control Handle Brake/Free Spool Position Sensor: Data Erratic, Intermittent, or Incorrect	Sensor Signal (PWM) - Test
3744-3	Winch Control Handle Brake/Free Spool Position Sensor: Voltage Above Normal	Sensor Signal (PWM) - Test
3744-4	Winch Control Handle Brake/Free Spool Position Sensor: Voltage Below Normal	Sensor Signal (PWM) - Test
3744-8	Winch Control Handle Brake/Free Spool Position Sensor: Abnormal Frequency, Pulse Width, or Period	Sensor Signal (PWM) - Test
3744-13	Winch Control Handle Brake/Free Spool Position Sensor: Out of Calibration	Sensor Signal (PWM) - Test
3797-3	Operator Seat Belt Switch: Voltage Above Normal	Switch Circuits - Test
3797-4	Operator Seat Belt Switch: Voltage Below Normal	Switch Circuits - Test
4019-2	Air Conditioner Suction Pressure Sensor: Data Erratic, Intermittent, or Incorrect	Sensor Signal (PWM) - Test
4019-3	Air Conditioner Suction Pressure Sensor: Voltage Above Normal	Sensor Signal (PWM) - Test
4019-4	Air Conditioner Suction Pressure Sensor: Voltage Below Normal	Sensor Signal (PWM) - Test
4019-8	Air Conditioner Suction Pressure Sensor: Abnormal Frequency, Pulse Width, Or Period	Sensor Signal (PWM) - Test
4022-2	Air Conditioner Compressor Discharge Pressure Sensor: Data Erratic, Intermittent, or Incorrect	Sensor Signal (PWM) - Test
4022-3	Air Conditioner Compressor Discharge Pressure Sensor: Voltage Above Normal	Sensor Signal (PWM) - Test
4022-4	Air Conditioner Compressor Discharge Pressure Sensor: Voltage Below Normal	Sensor Signal (PWM) - Test
4022-8	Air Conditioner Compressor Discharge Pressure Sensor: Abnormal Frequency, Pulse Width, Or Period	Sensor Signal (PWM) - Test
4651-2	Blade Inertial Measurement Sensor: Data Erratic, Intermittent, or Incorrect	CAN Data Link - Test
4651-9	Blade Inertial Measurement Sensor: Abnormal Update Rate	CAN Data Link - Test
4651-13	Blade Inertial Measurement Sensor: Out of Calibration	CAN Data Link - Test
5407-13	Tool Automation Implement Valve: Out of Calibration	Solenoid Valve - Test
5805-2	Communication Gateway: Data Erratic, Intermittent, or Incorrect	Ethernet Data Link - Test
5805-9	Communication Gateway: Abnormal Update Rate	Ethernet Data Link - Test
5885-2	Blade Lift Arm Inertial Measurement Sensor: Data Erratic, Intermittent or Incorrect	CAN Data Link - Test
5885-9	Blade Lift Arm Inertial Measurement Sensor: Abnormal Update Rate	CAN Data Link - Test
6419-3	Charge Pump Pressure Relief Valve Solenoid: Voltage Above Normal	Solenoid Valve - Test
6419-5	Charge Pump Pressure Relief Valve Solenoid: Current Below Normal	Solenoid Valve - Test
6419-6	Charge Pump Pressure Relief Valve Solenoid: Current Above Normal	Solenoid Valve - Test

Machine ECM

The following table lists the diagnostic codes for the Machine ECM. When a diagnostic code becomes active, refer to the Troubleshooting section of this manual for a specific troubleshooting procedure.

Show/hide table

Table 2
Diagnostic Trouble Codes For The Machine ECM
DTC	Description	Test Procedure
41-3	8 Volt DC Supply: Voltage Above Normal	Sensor Supply - Test
41-4	8 Volt DC Supply: Voltage Below Normal	Sensor Supply - Test
70-2	Parking Brake Switch: Data Erratic, Intermittent, or Incorrect	Operator Control Switch (Switch to Ground) - Test
70-3	Parking Brake Switch: Voltage Above Normal	Operator Control Switch (Switch to Ground) - Test
177-3	Transmission Oil Temperature Sensor: Voltage Above Normal	Sensor Signal ( Analog Passive) - Test
177-4	Transmission Oil Temperature Sensor: Voltage Below Normal	Sensor Signal ( Analog Passive) - Test
246-9	Proprietary CAN Data Link : Abnormal Update Rate	CAN Data Link - Test
246-14	Proprietary CAN Data Link : Special Instruction	CAN Data Link - Test
247-9	SAE J1939 Data Link: Abnormal Update Rate	CAN Data Link - Test
247-14	SAE J1939 Data Link: Special Instruction	CAN Data Link - Test
262-3	5 V Sensor DC Power Supply: Voltage Above Normal	Sensor Supply - Test
262-4	5 V Sensor DC Power Supply: Voltage Below Normal	Sensor Supply - Test
444-3	Starter Motor Relay: Voltage Above Normal	Relay - Test
444-5	Starter Motor Relay: Current Below Normal	Relay - Test
444-6	Starter Motor Relay: Current Above Normal	Relay - Test
473-3	Charge Pressure Sensor: Voltage Above Normal	Sensor Signal ( Analog Active) - Test
473-4	Charge Pressure Sensor: Voltage Below Normal	Sensor Signal ( Analog Active) - Test
585-2	Transmission Output Speed Sensor #1: Erratic, Intermittent, or Incorrect	Speed Sensor - Test
585-5	Transmission Output Speed Sensor #1: Current Below Normal	Speed Sensor - Test
585-6	Transmission Output Speed Sensor #1: Current Above Normal	Speed Sensor - Test
585-8	Transmission Output Speed Sensor #1: Abnormal Frequency, Pulse Width, or Period	Speed Sensor - Test
588-9	Monitoring System Display: Abnormal Update Rate	CAN Data Link - Test
590-9	Engine Control Module: Abnormal Update Rate	CAN Data Link - Test
590-14	Engine Control Module: Special Instruction	CAN Data Link - Test
596-9	Implement Control: Abnormal Update Rate	CAN Data Link - Test
596-14	Implement Control: Special Instruction	CAN Data Link - Test
637-6	Backup Alarm: Current Above Normal	Alarm - Test
673-2	Transmission Output Speed Sensor #2: Erratic, Intermittent, or Incorrect	Speed Sensor - Test
673-5	Transmission Output Speed Sensor #2: Current Below Normal	Speed Sensor - Test
673-6	Transmission Output Speed Sensor #2: Current Above Normal	Speed Sensor - Test
673-8	Transmission Output Speed Sensor #2: Abnormal Frequency, Pulse Width, or Period	Speed Sensor - Test
674-5	Transmission Intermediate Speed Sensor #1: Current Below Normal	Speed Sensor - Test
674-6	Transmission Intermediate Speed Sensor #1: Current Above Normal	Speed Sensor - Test
675-5	Transmission Intermediate Speed Sensor #2: Current Below Normal	Speed Sensor - Test
675-6	Transmission Intermediate Speed Sensor #2: Current Above Normal	Speed Sensor - Test
681-3	Parking Brake Solenoid: Voltage Above Normal	Solenoid Valve (Switch Controlled) - Test
681-5	Parking Brake Solenoid: Current Below Normal	Solenoid Valve (Switch Controlled) - Test
681-6	Parking Brake Solenoid: Current Above Normal	Solenoid Valve (Switch Controlled) - Test
709-3	Transmission Lockup Clutch Solenoid: Voltage Above Normal	Solenoid Valve - Test
709-5	Transmission Lockup Clutch Solenoid: Current Below Normal	Solenoid Valve - Test
709-6	Transmission Lockup Clutch Solenoid: Current Above Normal	Solenoid Valve - Test
718-13	Transmission System: Out of Calibration	Perform the "Transmission Clutch Fill Calibration"
726-3	Right Steering Solenoid: Voltage Above Normal	Solenoid Valve - Test
726-5	Right Steering Solenoid: Current Below Normal	Solenoid Valve - Test
726-6	Right Steering Solenoid: Current Above Normal	Solenoid Valve - Test
726-13	Right Steering Solenoid: Out Of Calibration	Solenoid Valve - Test
727-3	Left Steering Solenoid: Voltage Above Normal	Solenoid Valve - Test
727-5	Left Steering Solenoid: Current Below Normal	Solenoid Valve - Test
727-6	Left Steering Solenoid: Current Above Normal	Solenoid Valve - Test
727-13	Left Steering Solenoid: Out Of Calibration	Solenoid Valve - Test
826-3	Torque Converter Oil Temperature Sensor: Voltage Above Normal	Sensor Signal ( Analog Passive) - Test
826-4	Torque Converter Oil Temperature Sensor: Voltage Below Normal	Sensor Signal ( Analog Passive) - Test
1326-2	ECM Location Code: Data Erratic, Intermittent, or Incorrect	ECM Location Code - Test
1401-3	Transmission Solenoid 1: Voltage Above Normal	Solenoid Valve - Test
1401-5	Transmission Solenoid 1: Current Below Normal	Solenoid Valve - Test
1401-6	Transmission Solenoid 1: Current Above Normal	Solenoid Valve - Test
1402-3	Transmission Solenoid 2: Voltage Above Normal	Solenoid Valve - Test
1402-5	Transmission Solenoid 2: Current Below Normal	Solenoid Valve - Test
1402-6	Transmission Solenoid 2: Current Above Normal	Solenoid Valve - Test
1403-3	Transmission Solenoid 3: Voltage Above Normal	Solenoid Valve - Test
1403-5	Transmission Solenoid 3: Current Below Normal	Solenoid Valve - Test
1403-6	Transmission Solenoid 3: Current Above Normal	Solenoid Valve - Test
1404-3	Transmission Solenoid 4: Voltage Above Normal	Solenoid Valve - Test
1404-5	Transmission Solenoid 4: Current Below Normal	Solenoid Valve - Test
1404-6	Transmission Solenoid 4: Current Above Normal	Solenoid Valve - Test
1405-3	Transmission Solenoid 5: Voltage Above Normal	Solenoid Valve - Test
1405-5	Transmission Solenoid 5: Current Below Normal	Solenoid Valve - Test
1405-6	Transmission Solenoid 5: Current Above Normal	Solenoid Valve - Test
1406-3	Transmission Solenoid 6: Voltage Above Normal	Solenoid Valve - Test
1406-5	Transmission Solenoid 6: Current Below Normal	Solenoid Valve - Test
1406-6	Transmission Solenoid 6: Current Above Normal	Solenoid Valve - Test
1435-9	System Master Control Module: Abnormal Update Rate	CAN Data Link - Test
1435-14	System Master Control Module: Special Instruction	CAN Data Link - Test
1469-8	Steering Motor Speed Sensor #1: Abnormal Frequency, Pulse Width, or Period	Sensor Signal (PWM) - Test
1470-8	Steering Motor Speed Sensor #2: Abnormal Frequency, Pulse Width, or Period	Sensor Signal (PWM) - Test
1471-2	Steering Control Position Sensor #1: Data Erratic, Intermittent, or Incorrect	Sensor Signal (PWM) - Test
1471-3	Steering Control Position Sensor #1: Voltage Above Normal	Sensor Signal (PWM) - Test
1471-4	Steering Control Position Sensor #1: Voltage Below Normal	Sensor Signal (PWM) - Test
1471-8	Steering Control Position Sensor #1: Abnormal Frequency, Pulse Width, or Period	Sensor Signal (PWM) - Test
1471-13	Steering Control Position Sensor #1: Out of Calibration	Sensor Signal (PWM) - Test
1472-2	Steering Control Position Sensor #2: Data Erratic, Intermittent, or Incorrect	Sensor Signal (PWM) - Test
1472-3	Steering Control Position Sensor #2: Voltage Above Normal	Sensor Signal (PWM) - Test
1472-4	Steering Control Position Sensor #2: Voltage Below Normal	Sensor Signal (PWM) - Test
1472-8	Steering Control Position Sensor #2: Abnormal Frequency, Pulse Width, or Period	Sensor Signal (PWM) - Test
1472-13	Steering Control Position Sensor #2: Out of Calibration	Sensor Signal (PWM) - Test
1482-3	10 Volt Sensor DC Power Supply: Voltage Above Normal	Sensor Supply - Test
1482-4	10 Volt Sensor DC Power Supply : Voltage Below Normal	Sensor Supply - Test
1579-6	Transmission Lube Flow Valve Solenoid: Current Above Normal	Solenoid Valve - Test
1639-2	Machine Security System Module: Erratic, Intermittent, or Incorrect	CAN Data Link - Test
1639-9	Machine Security System Module: Abnormal Update Rate	CAN Data Link - Test
1677-6	Solenoid Return #4: Current Above Normal	Solenoid Return - Test
1678-4	Solenoid Return #5: Voltage Below Normal	Solenoid Return - Test
1678-5	Solenoid Return #5: Current Below Normal	Solenoid Return - Test
2300-9	Switch Panel: Abnormal Update Rate	CAN Data Link - Test
2348-9	SAE J1939 Data Link #2: Abnormal Update Rate	CAN Data Link - Test
2348-14	SAE J1939 Data Link #2: Special Instruction	CAN Data Link - Test
2500-2	Power Train Speed Range Control position Sensor: Data Erratic, Intermittent, or Incorrect	Sensor Signal (PWM) - Test
2500-3	Power Train Speed Range Control position Sensor: Voltage Above Normal	Sensor Signal (PWM) - Test
2500-4	Power Train Speed Range Control position Sensor: Voltage Below Normal	Sensor Signal (PWM) - Test
2500-8	Power train Speed Range Control Position Sensor: Abnormal Frequency, Pulse Width, or Period	Sensor Signal (PWM) - Test
2596-3	Brake Pressure Modulation Solenoid: Voltage Above Normal	Solenoid Valve (Switch Controlled) - Test
2596-5	Brake Pressure Modulation Solenoid: Current Below Normal	Solenoid Valve (Switch Controlled) - Test
2596-6	Brake Pressure Modulation Solenoid: Current Above Normal	Solenoid Valve (Switch Controlled) - Test
2596-13	Brake Pressure Modulation Solenoid: Out of Calibration	Solenoid Valve (Switch Controlled) - Test
2993-2	Direction Selector Position Sensor #1: Data Erratic, Intermittent, or Incorrect	Sensor Signal (PWM) - Test
2993-3	Direction Selector Position Sensor #1: Voltage Above Normal	Sensor Signal (PWM) - Test
2993-4	Direction Selector Position Sensor #1: Voltage Below Normal	Sensor Signal (PWM) - Test
2993-8	Direction Selector Position Sensor #1: Abnormal Frequency, Pulse Width, or Period	Sensor Signal (PWM) - Test
2994-2	Direction Selector Position Sensor #2: Data Erratic, Intermittent, or Incorrect	Sensor Signal (PWM) - Test
2994-3	Direction Selector Position Sensor #2: Voltage Above Normal	Sensor Signal (PWM) - Test
2994-4	Direction Selector Position Sensor #2: Voltage Below Normal	Sensor Signal (PWM) - Test
2994-8	Direction Selector Position Sensor #2: Abnormal Frequency, Pulse Width, or Period	Sensor Signal (PWM) - Test
3467-6	Main Power Relay: Current Above Normal	Relay -Test
3527-2	Direction Selector: (Power train) Direction Selector: Data Erratic, Intermittent or Incorrect	Switch Circuits - Test
3642-3	Operator Speed Set/Recall Switch: Voltage Above Normal	Switch Circuits - Test
3642-4	Operator Speed Set/Recall Switch: Voltage Below Normal	Switch Circuits - Test
3652-2	Steering Pump Oil Pressure #1 Sensor: Data Erratic, Intermittent or Incorrect	Sensor Signal (PWM) - Test
3652-3	Steering Pump Oil Pressure #1 Sensor: Voltage Above Normal	Sensor Signal (PWM) - Test
3652-4	Steering Pump Oil Pressure #1 Sensor: Voltage Below Normal	Sensor Signal (PWM) - Test
3652-8	Steering Pump Oil Pressure #1 Sensor: Abnormal Frequency, Pulse Width, or Period	Sensor Signal (PWM) - Test
3653-2	Steering Pump Oil Pressure #2 Sensor: Data Erratic, Intermittent or Incorrect	Sensor Signal (PWM) - Test
3653-3	Steering Pump Oil Pressure #2 Sensor: Voltage Above Normal	Sensor Signal (PWM) - Test
3653-4	Steering Pump Oil Pressure #2 Sensor: Voltage Below Normal	Sensor Signal (PWM) - Test
3653-8	Steering Pump Oil Pressure #2 Sensor: Abnormal Frequency, Pulse Width, or Period	Sensor Signal (PWM) - Test
3657-3	Operator In Seat Sensor: Voltage Above Normal	Sensor Signal ( Analog Passive) - Test
3657-4	Operator In Seat Sensor: Voltage Below Normal	Sensor Signal ( Analog Passive) - Test
4929-2	Transmission Input Speed #1 Sensor: Erratic, Intermittent, or Incorrect	Speed Sensor - Test
4930-2	Transmission Input Speed #2 Sensor: Erratic, Intermittent, or Incorrect	Speed Sensor - Test
5001-2	Right Pedal Position Sensor: Data Erratic, Intermittent or Incorrect	Sensor Signal (PWM) - Test
5001-3	Right Pedal Position Sensor: Voltage Above Normal	Sensor Signal (PWM) - Test
5001-4	Right Pedal Position Sensor: Voltage Below Normal	Sensor Signal (PWM) - Test
5001-8	Right Pedal Position Sensor: Abnormal Frequency, Pulse Width, or Period	Sensor Signal (PWM) - Test
5002-2	Right Pedal Position Sensor: Data Erratic, Intermittent or Incorrect	Sensor Signal (PWM) - Test
5002-3	Left Pedal Position Sensor: Voltage Above Normal	Sensor Signal (PWM) - Test
5002-4	Left Pedal Position Sensor: Voltage Below Normal	Sensor Signal (PWM) - Test
5002-8	Left Pedal Position Sensor: Abnormal Frequency, Pulse Width, or Period	Sensor Signal (PWM) - Test
5002-13	Left Pedal Position Sensor: Out of Calibration	Sensor Signal (PWM) - Test
5874-9	Bluetooth Transceiver: Abnormal Update Rate	CAN Data Link - Test
5922-2	Steering Control Position Sensor: Data Erratic, Intermittent or Incorrect	Sensor Signal (PWM) - Test
6307-5	Torque Converter Output Speed Sensor #1: Current Below Normal	Speed Sensor - Test
6307-6	Torque Converter Output Speed Sensor #1: Current Above Normal	Speed Sensor - Test
6307-8	Torque Converter Output Speed Sensor #1: Abnormal Frequency, Pulse Width, or Period	Speed Sensor - Test
6308-5	Torque Converter Output Speed Sensor #2: Current Below Normal	Speed Sensor - Test
6308-6	Torque Converter Output Speed Sensor #2: Current Above Normal	Speed Sensor - Test
6308-8	Torque Converter Output Speed Sensor #2: Abnormal Frequency, Pulse Width, or Period	Speed Sensor - Test