992K Wheel Loader Electrohydraulic System MID 082 - CID 0360 - FMI 11 Caterpillar


MID 082 - CID 0360 - FMI 11
`
MID 082 CID 0360 FMI 11

Conditions Which Generate This Code:



Illustration 1g01970713
Schematic for the "Lower KO Detent" Solenoid

This diagnostic code FMI 11 is recorded when the interface module has an internal failure.

System Response:

When this diagnostic code CID 0360 FMI 11 is active, the AVSpare Electronic Technician (ET) will be unable to control the solenoid for the warm up valve. The ET will read the voltage of the solenoid circuit as being below normal, which is an indication of an open circuit. The ET will be unable to energize the solenoid.

Test Step 1. CHECK THE IMPLEMENT ECM

  1. Turn the key start switch and the disconnect switch to the OFF position.

  2. Wait for 30 seconds.

  3. Turn the disconnect switch to the ON position.

  4. Allow the self test to run fully before you proceed to the next step.

  5. Check the message center for an active diagnostic code.

Expected Result:

The diagnostic code CID 0360 FMI 11 is no longer present.

Results:

  • OK - The diagnostic code CID 0360 FMI 11 is no longer present. Resetting the interface module has resolved the diagnostic code.

    STOP

  • NOT OK - The diagnostic code CID 0360 FMI 11 is still active. The interface module has failed.

    Repair: Check the circuit again. Use the AVSpare Electronic Technician (Cat ET) service tool, in order to perform a Wiggle Test on the machine wiring harness. The Wiggle Test can detect momentary shorts, intermittent shorts or opens in the machine wiring harness.

    It is unlikely that the ECU has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. Prior to replacing an ECM, always contact your dealership's Technical Communicator for possible consultation with AVSpare. This consultation may greatly reduce repair time. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace".

    STOP

Information System:

C4.4 Industrial Engine Engine Oil Level - Check
3500 Engines Flywheel Housing
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0600 - FMI 06
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0600 - FMI 06
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0600 - FMI 04
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0600 - FMI 04
992K Wheel Loader Electrohydraulic System MID 082 - CID 0359 - FMI 11
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0600 - FMI 03
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0600 - FMI 03
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0600 - FMI 08
3500B and 3500C Marine Engines Turbocharger
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0600 - FMI 08
992K Wheel Loader Electrohydraulic System MID 082 - CID 0361 - FMI 11
988H Wheel Loader Electrohydraulic System Main Control Valve
2009/11/12 Protective Covers For the Equalizer Bar Are Now Used On the D11T {7206}
992K Wheel Loader Electrohydraulic System MID 082 - CID 0463 - FMI 03
992K Wheel Loader Electrohydraulic System MID 082 - CID 0463 - FMI 05
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMS<SUP>TM MID 049 - CID 0890 - FMI 09
992K Wheel Loader Electrohydraulic System MID 082 - CID 0463 - FMI 06
992K Wheel Loader Electrohydraulic System MID 082 - CID 0463 - FMI 11
3500 Engines Housing (Front)
992K Wheel Loader Electrohydraulic System MID 082 - CID 2360 - FMI 04
992K Wheel Loader Electrohydraulic System MID 082 - CID 0590 - FMI 14
992K Wheel Loader Electrohydraulic System MID 082 - CID 1571 - FMI 11