992K Wheel Loader Electrohydraulic System MID 082 - CID 2408 - FMI 06 Caterpillar


MID 082 - CID 2408 - FMI 06
`
MID 082 CID 2408 FMI 06

Conditions Which Generate This Code:



Illustration 1g01968653
Schematic for the Left Float Valve Solenoid

This diagnostic code is associated with the Left Float Valve Solenoid. The FMI 06 means that the ECM has determined that there is a short to ground in the solenoid circuit.

The possible causes for this diagnostic code are listed below:

  • The internal windings for the solenoid have low impedance.

  • The internal windings for the solenoid are shorted.

  • The signal circuit from the ECM to the solenoid is shorted to ground.

System Response:

The machine response is listed:

Since hydraulic flow to the cylinder is supplied by two control valves, the dump function is possible at a reduced rate.

Note: The following test procedure may create other diagnostic codes. Clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 2408 FMI 06 is active before performing this procedure.

Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.

Test Step 1. CHECK THE SOLENOID

  1. Turn the disconnect switch and the key start switch to the ON position.

    Note: Do not start the engine.

  2. Observe the status of the diagnostic code.

  3. Disconnect the solenoid with the active diagnostic code from the machine harness.

Expected Result:

The CID 2408 FMI 06 changes to CID 2408 FMI 05 when the solenoid is disconnected.

Results:

  • YES - The CID 2408 FMI 06 changes to CID 2408 FMI 05 when the solenoid is disconnected. The circuit is correct.

    Repair: The solenoid has failed. Repeat this test "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid. Verify that the new solenoid corrects the problem.

    STOP

  • NO - The CID 2408 FMI 06 remains active. Proceed to Test Step 2.

Test Step 2. CHECK THE ENERGIZER CIRCUIT OF THE SOLENOID FOR A SHORT TO GROUND

  1. Turn the key start switch and the disconnect switch to the OFF position.

  2. The solenoid remains disconnected from the machine harness.

  3. Disconnect the machine harness connector(s) from the ECM.

  4. At the machine harness connector, measure the resistance from the signal contact J2-5 (wire G729-OR(Orange)) to all contacts that are used in the machine harness connectors for the ECM.

Expected Result:

Each resistance measurement is greater than 5000 ohms.

Results:

  • OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.

  • NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J2-5 (wire G729-OR(Orange)) and the circuit with the low resistance measurement.

    Repair: Repair the machine harness or replace the machine harness.

    STOP

Test Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS

  1. Inspect the harness connectors and clean the contacts of the harness connectors.

  2. Reconnect all harness connectors.

  3. Turn the disconnect switch and the key start switch to the ON position.

  4. Operate the machine.

  5. Check the status of the CID 2408 FMI 06.

Expected Result:

The CID 2408 FMI 06 is active.

Results:

  • YES - The CID 2408 FMI 06 is active. The diagnostic code has not been corrected. The ECM may have failed.

    Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, the ECM may have failed. Prior to replacing an ECM, always contact your dealership's Technical Communicator for possible consultation with AVSpare. This consultation may greatly reduce repair time. If the ECM requires replacement, refer to Testing and Adjusting, "Electronic Control Module (ECM) - Replace".

    STOP

  • NO - The CID 2408 FMI 06 is not active. The diagnostic code does not exist at this time.

    Repair: The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.

    STOP

Information System:

992K Wheel Loader Electrohydraulic System MID 082 - CID 2408 - FMI 05
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0427 - FMI 03
992K Wheel Loader Electrohydraulic System MID 082 - CID 2408 - FMI 03
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0427 - FMI 03
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0427 - FMI 08
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0427 - FMI 08
Pilot Oil Pressure Reducing Valve Retrofit{5467}
D7E Track-Type Tractor Camera - If Equipped
Tier III Level Emissions Engine Retrofit for a 980C, 980F, and a 980F Series II Wheel Loader {1000, 1000, 7000}
992K Wheel Loader Electrohydraulic System MID 082 - CID 2409 - FMI 06
992K Wheel Loader Electrohydraulic System MID 082 - CID 2409 - FMI 05
992K Wheel Loader Electrohydraulic System MID 082 - CID 1571 - FMI 13
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0427 - FMI 04
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0427 - FMI 04
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0427 - FMI 06
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0427 - FMI 06
992K Wheel Loader Electrohydraulic System MID 082 - CID 2405 - FMI 03
992K Wheel Loader Electrohydraulic System MID 082 - CID 2405 - FMI 05
992K Wheel Loader Electrohydraulic System MID 082 - CID 2405 - FMI 06
992K Wheel Loader Electrohydraulic System MID 082 - CID 2405 - FMI 13
992K Wheel Loader Electrohydraulic System MID 082 - CID 2409 - FMI 11
992K Wheel Loader Electrohydraulic System MID 082 - CID 2405 - FMI 11
992K Wheel Loader Electrohydraulic System MID 082 - CID 2408 - FMI 11
992K Wheel Loader Electrohydraulic System MID 082 - CID 2576 - FMI 03