992K Wheel Loader Electrohydraulic System MID 082 - CID 2408 - FMI 05 Caterpillar


MID 082 - CID 2408 - FMI 05
`
MID 082 CID 2408 FMI 05

Conditions Which Generate This Code:



Illustration 1g01968653
Schematic for the Left Float Valve Solenoid

This diagnostic code is associated with the Left Float Valve Solenoid. The FMI 05 means that the ECM has determined that an open in the circuit exists.

The possible causes for this diagnostic code are listed below:

  • The signal circuit from the ECM to the solenoids is open.

  • The return circuit from the solenoid is open.

  • The internal windings for the solenoid have high impedance.

  • The internal windings for the solenoid are open.

System Response:

The machine response is listed:

Since the hydraulic flow to the cylinder is supplied by two control valves, the dump function is possible at a reduced rate.

Note: The following test procedure may create other diagnostic codes. Clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 2408 FMI 05 is active before performing this procedure.

Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.

Test Step 1. CHECK THE SOLENOID

  1. Turn the disconnect switch and the key start switch to the ON position.

    Note: Do not start the engine.

  2. Disconnect the solenoid with the active diagnostic code from the machine harness.

  3. At the machine harness connector for the solenoid, place a jumper wire from contact 1 (wire G729-OR(Orange)) to contact 2 (wire R799-BR(Brown)).

  4. Observe the status of the CID 2408 FMI 05.

Expected Result:

The CID 2408 FMI 05 remains active. The FMI has not changed and the "05" is still active.

Results:

  • YES - The diagnostic code remains active. The jumper wire does not affect the diagnostic code. Proceed to Test Step 2.

  • NO - The diagnostic is no longer active. The solenoid has failed.

    Repair: The solenoid has failed. Repeat this Test Step "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid. Verify that the new solenoid corrects the problem.

    STOP

Test Step 2. CHECK THE HARNESS FOR AN OPEN

  1. Turn the key start switch and the disconnect switch to the OFF position.

  2. Disconnect the machine harness connector(s) from the ECM.

  3. The jumper wire that was installed in the previous Test Step remains in place.

  4. At the machine harness connector, measure the resistance from signal contact J2-5 (wire G729-OR(Orange)) to contact J2-8 (wire R799-BR(Brown)).

Expected Result:

The resistance is less than 5.0 ohms.

Results:

  • OK - The resistance is less than 5.0 ohms. The machine harness is correct. Proceed to Test Step 3.

  • NOT OK - The resistance is greater than 5000 ohms. The resistance measurement is not correct. There is an open circuit in the machine harness.

    Repair: The open is in wire G729-OR(Orange) or in wire R799-BR(Brown) of the machine harness. Repair the machine harness or replace the machine harness.

    STOP

Test Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS

  1. Inspect the contacts of the harness connectors and clean the harness connectors.

  2. Reconnect all harness connectors.

  3. Turn the disconnect switch and the key start switch to the ON position.

  4. Operate the machine.

  5. Check the status of the CID 2408 FMI 05.

Expected Result:

The CID 2408 FMI 05 is active.

Results:

  • YES - The CID 2408 FMI 05 is active. The diagnostic code has not been corrected. The ECM may have failed.

    Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, the ECM may have failed. Prior to replacing an ECM, always contact your dealership's Technical Communicator for possible consultation with AVSpare. This consultation may greatly reduce repair time. If the ECM requires replacement, refer to the Testing and Adjusting, "Electronic Control Module (ECM) - Replace" Story in this manual.

    STOP

  • NO - The CID 2408 FMI 05 is not active. The diagnostic code does not exist at this time.

    Repair: The initial diagnostic code was probably caused by a poor electrical connection at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.

    STOP

Information System:

854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0427 - FMI 03
992K Wheel Loader Electrohydraulic System MID 082 - CID 2408 - FMI 03
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0427 - FMI 03
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0427 - FMI 08
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0427 - FMI 08
Pilot Oil Pressure Reducing Valve Retrofit{5467}
D7E Track-Type Tractor Camera - If Equipped
Tier III Level Emissions Engine Retrofit for a 980C, 980F, and a 980F Series II Wheel Loader {1000, 1000, 7000}
992K Wheel Loader Electrohydraulic System MID 082 - CID 2409 - FMI 06
992K Wheel Loader Electrohydraulic System MID 082 - CID 2409 - FMI 05
992K Wheel Loader Electrohydraulic System MID 082 - CID 1571 - FMI 13
992K Wheel Loader Electrohydraulic System MID 082 - CID 2409 - FMI 03
992K Wheel Loader Electrohydraulic System MID 082 - CID 2408 - FMI 06
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0427 - FMI 04
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0427 - FMI 04
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0427 - FMI 06
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0427 - FMI 06
992K Wheel Loader Electrohydraulic System MID 082 - CID 2405 - FMI 03
992K Wheel Loader Electrohydraulic System MID 082 - CID 2405 - FMI 05
992K Wheel Loader Electrohydraulic System MID 082 - CID 2405 - FMI 06
992K Wheel Loader Electrohydraulic System MID 082 - CID 2405 - FMI 13
992K Wheel Loader Electrohydraulic System MID 082 - CID 2409 - FMI 11
992K Wheel Loader Electrohydraulic System MID 082 - CID 2405 - FMI 11
992K Wheel Loader Electrohydraulic System MID 082 - CID 2408 - FMI 11