992K Wheel Loader Electrohydraulic System MID 082 - CID 1571 - FMI 13 Caterpillar


MID 082 - CID 1571 - FMI 13
`
MID 082 CID 1571 FMI 13

Conditions Which Generate This Code:



Illustration 1g01964859
Schematic for the right rear implement pump solenoid

This diagnostic code is associated with the Right Rear Implement Pump Solenoid. The FMI 13 means that the ECM has determined that the solenoid needs calibration. Once the calibration for the solenoid has been performed successfully, this diagnostic code will disappear. This failure is active on a new ECM.

Possible causes of this diagnostic code are listed below:

  • The ECM has been replaced or new software has been installed.

  • The calibration procedure has failed.

System Response:

The deadband in the control lever will be excessive. The operation of the control lever will be jerky.

Note: Ensure that you have repaired any condition that would cause other active diagnostic codes that are related to this solenoid. For example, the CID 1571 FMI 03 or FMI 05 are not active when the CID 1571 FMI 13 is active. If the other diagnostic codes are active, troubleshoot those codes first. Then perform this procedure.

Note: Ensure that the diagnostic code of CID 1571 FMI 13 is active before performing this procedure.

Test Step 1. CHECK THE CALIBRATION

  1. Perform the calibration procedure. Refer to the Testing and Adjusting section of the Service Manual for the correct procedure.

  2. Observe the status of the CID 1571 FMI 13.

Expected Result:

The CID 1571 FMI 13 is active.

Results:

  • YES - The CID 1571 FMI 13 is active. The diagnostic code has not been corrected. Verify that the correct software has been flashed into the ECM, or that the correct ECM is installed on the machine. Then repeat the calibration.

    Repair: If the diagnostic code is still active and the cause of the diagnostic code is not found, the ECM may have failed. It is unlikely that the ECM has failed. Verify that the solenoid and associated circuits are correct. Prior to replacing an ECM, always contact your dealership for possible consultation with AVSpare. This consultation may greatly reduce repair time. If the ECM requires replacement, refer to Testing and Adjusting, "Electronic Control Module (ECM) - Replace".

    STOP

  • NO - The CID 1571 FMI 13 is not active. The calibration corrected the condition that caused the diagnostic code.

    Repair: Resume normal operation.

    STOP

Information System:

992K Wheel Loader Electrohydraulic System MID 082 - CID 2409 - FMI 03
992K Wheel Loader Electrohydraulic System MID 082 - CID 2415 - FMI 08
992K Wheel Loader Electrohydraulic System MID 082 - CID 2415 - FMI 04
992K Wheel Loader Electrohydraulic System MID 082 - CID 2415 - FMI 03
992K Wheel Loader Electrohydraulic System MID 082 - CID 2415 - FMI 01
992K Wheel Loader Electrohydraulic System MID 082 - CID 2415 - FMI 00
992K Wheel Loader Electrohydraulic System MID 082 - CID 2416 - FMI 08
992K Wheel Loader Electrohydraulic System MID 082 - CID 2416 - FMI 04
C9.3 Tier 4 Final Engines Air in Fuel - Test
992K Wheel Loader Electrohydraulic System MID 082 - CID 2416 - FMI 03
992K Wheel Loader Electrohydraulic System MID 082 - CID 1571 - FMI 06
992K Wheel Loader Electrohydraulic System MID 082 - CID 1571 - FMI 05
992K Wheel Loader Electrohydraulic System MID 082 - CID 2409 - FMI 05
992K Wheel Loader Electrohydraulic System MID 082 - CID 2409 - FMI 06
Tier III Level Emissions Engine Retrofit for a 980C, 980F, and a 980F Series II Wheel Loader {1000, 1000, 7000}
D7E Track-Type Tractor Camera - If Equipped
Pilot Oil Pressure Reducing Valve Retrofit{5467}
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0427 - FMI 08
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0427 - FMI 08
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0427 - FMI 03
992K Wheel Loader Electrohydraulic System MID 082 - CID 2408 - FMI 03
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0427 - FMI 03
992K Wheel Loader Electrohydraulic System MID 082 - CID 2408 - FMI 05
992K Wheel Loader Electrohydraulic System MID 082 - CID 2408 - FMI 06