854K Wheel Dozer and 992K Wheel Loader Power Train MID 081 - CID 0262 - FMI 04 Caterpillar


MID 081 - CID 0262 - FMI 04
`

Conditions Which Generate This Code:

This diagnostic code is associated with the 5 volt power supply for the sensors. The FMI 04 means that the ECM has determined that the voltage of the sensor circuit is below normal.

The possible causes of the diagnostic code are listed below:

  • A sensor has failed.

  • The supply circuit is shorted to ground.

  • ECM has failed. This is unlikely.

Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all of the connections in the circuit are clean and secure. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.

Note: The following test procedure may create other diagnostic codes. Clear these diagnostic codes when the problem has been corrected. Verify that the CID 0262 FMI 04 is active before performing this procedure.

Use a digital multimeter for the measurements in this procedure.

System Response:

All of the sensors that receive power from the 5 volt supply are disabled.

Test Step 1. CHECK THE VOLTAGE AT THE ECM

  1. Turn the disconnect switch and the key start switch to the ON position.

  1. Check the voltage at the ECM connector for sensor supply to a ground contact. Do not disconnect the machine harness from the ECM. Do not disconnect the machine harness from the ECM.

Expected Result:

The voltage is 5.0 ± 0.5 DCV.

Results:

  • OK - The voltage is 5.0 ± 0.5 DCV. The sensor supply voltage is correct. Verify that the same diagnostic code is present. If the diagnostic code is still present the ECM may have failed.

    Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. Prior to replacing an ECM, always contact your dealership's Technical Communicator for possible consultation with AVSpare. This consultation may greatly reduce repair time. If the ECM requires replacement, refer to Troubleshooting, "Electronic Control Module (ECM) - Replace".

    STOP

  • NOT OK - The voltage is not 5.0 ± 0.5 DCV. The voltage is less than 5.0 ± 0.5 DCV. The sensor supply voltage is not correct. Proceed to Test Step 2.

Test Step 2. CHECK FOR A SHORT TO GROUND

  1. Turn the key start switch and the disconnect switch to the OFF position.

  1. Disconnect the machine harness from the ECM.

  1. At the machine harness connector for the ECM, measure the voltage from the contact for sensor supply to a ground contact.

Expected Result:

The resistance is greater than 5000 ohms.

Results:

  • OK - The resistance is greater than 5000 ohms. Verify that the same diagnostic code is present. If the diagnostic code is still present the ECM may have failed.

    Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. Prior to replacing an ECM, always contact your dealership's Technical Communicator for possible consultation with AVSpare. This consultation may greatly reduce repair time. If the ECM requires replacement, refer to Troubleshooting, "Electronic Control Module (ECM) - Replace".

    STOP

  • NOT OK - Resistance is less than 5 ohms. The machine harness has failed or a sensor has failed. Proceed to Test Step 3.

Test Step 3. DISCONNECT THE SENSORS

  1. The key start switch and the disconnect switch remain in the OFF position.

  1. One at a time, disconnect any sensor that uses the power supply from the machine harness.

  1. After disconnecting each sensor, check the resistance from the contact for the frame ground at the harness connector for the ECM.

Expected Result:

After disconnecting a particular sensor, the resistance changes and the resistance is greater than 5000 ohms.

Results:

  • YES - After disconnecting a particular sensor, the resistance changes and the resistance is greater than 5000 ohms. The sensor that was just disconnected has failed.

    Repair: Replace the sensor.

    STOP

  • NO - After disconnecting all of the sensors, the resistance is less than 5 ohms. The machine harness is shorted to ground.

    Repair: Repair the machine harness or replace the machine harness.

    STOP

Information System:

854K Wheel Dozer and 992K Wheel Loader Power Train MID 081 - CID 0262 - FMI 03
D7R Series II Track-Type Tractor Safety Messages
2013/01/14 A New Idler Pulley Assembly Is Now Used For the D8T, 583T, and 587T {1405, 1802, 7320}
992K Wheel Loader Electrohydraulic System MID 082 - CID 2416 - FMI 01
Documenting the Date Codes of the Bearings for 3500 and G3600 Engines{1202, 1225}
992K Wheel Loader Electrohydraulic System MID 082 - CID 2416 - FMI 00
C7.1 Industrial Engine Starting with Jump Start Cables - Do Not Use This Procedure in Hazardous Locations that have Explosive Atmospheres
988G Wheel Loader Power Train MID 081 - CID 0603 - FMI 03
D7R Series II Track-Type Tractor Specifications
D11T Track-Type Tractor Automatic Lubrication System General Information
PL61 Pipelayer Declaration of Conformity
TS180, TS185, TS220 and TS225 Towed Scrapers Maintenance Interval Schedule
992K Wheel Loader Electrohydraulic System MID 082 - CID 1571 - FMI 05
992K Wheel Loader Electrohydraulic System MID 082 - CID 1571 - FMI 06
992K Wheel Loader Electrohydraulic System MID 082 - CID 2416 - FMI 03
C9.3 Tier 4 Final Engines Air in Fuel - Test
992K Wheel Loader Electrohydraulic System MID 082 - CID 2416 - FMI 04
992K Wheel Loader Electrohydraulic System MID 082 - CID 2416 - FMI 08
992K Wheel Loader Electrohydraulic System MID 082 - CID 2415 - FMI 00
992K Wheel Loader Electrohydraulic System MID 082 - CID 2415 - FMI 01
992K Wheel Loader Electrohydraulic System MID 082 - CID 2415 - FMI 03
992K Wheel Loader Electrohydraulic System MID 082 - CID 2415 - FMI 04
992K Wheel Loader Electrohydraulic System MID 082 - CID 2415 - FMI 08
992K Wheel Loader Electrohydraulic System MID 082 - CID 2409 - FMI 03