950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train MID 081 - CID 0070 - FMI 04 Caterpillar


MID 081 - CID 0070 - FMI 04
`
950G Series II Wheel Loader, 962G Series II <BR>Wheel Loader and <BR> IT62G Series II Integrated Toolcarrier Power Train [RENR4310]
BRAKING SYSTEM
BRAKE GP
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train MID 081 - CID 0070 - FMI 04
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train MID 081 - CID 0070 - FMI 03

Conditions Which Generate This Code:




Illustration 1g00824088

Schematic for the parking brake pressure switch

This diagnostic code is associated with the parking brake pressure switch. The switch is connected to two inputs of the ECM. The inputs are "Normally Open" and "Normally Closed". One of the inputs is open and the other input is grounded during proper operation.

The FMI 04 means that the ECM has determined that the "Normally Open" and "Normally Closed" circuits are grounded.

Note: The following test procedure may create other diagnostic codes. Ignore these diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0070 FMI 04 is active before performing this procedure.

Test Step 1. CHECK THE SWITCH

  1. Turn the key start switch and the disconnect switch to the OFF position.

  1. Disconnect the machine harness from the switch.

  1. Turn the key start switch and the disconnect switch to the ON position.

Expected Result:

The CID 0070 FMI 04 has been replaced by CID 0070 FMI 03.

Results:

  • OK - The CID 0070 FMI 04 has been replaced by CID 0070 FMI 03. The machine harness and the ECM are correct. Proceed to Test Step 3.

  • NOT OK - The CID 0070 FMI 04 is still active. Proceed to Test Step 2.

Test Step 2. CHECK THE HARNESS

  1. Turn the disconnect switch and the key start switch to the OFF position.

  1. The machine harness remains disconnected from the switch.

  1. Disconnect the machine harness connector(s) from the ECM.

  1. Measure the resistance between contacts J1-27 (wire G764-PK) and J1-36 (wire 419-YL) of the machine harness to all the contacts that are used in machine harness connectors for the ECM.

Expected Result:

Each resistance measurement is greater than 5000 ohms.

Results:

  • OK - Each resistance measurement is greater than 5000 ohms. Proceed to Test Step 3.

  • NOT OK - One or more of the resistance measurements are less than 5 ohms. The harness has failed. The short is between J1-27 (wire G764-PK) and the circuit with the lowest resistance or the short is between J1-36 (wire 419-YL) and the circuit with the lowest resistance.

    Repair: Repair the wiring harness or replace the wiring harness.

    STOP

Test Step 3. CHECK THE OPERATION OF THE SWITCH

  1. The machine harness remains disconnected from the switch.

  1. Connect one lead from a multimeter to contact A of the harness connector for the switch.

  1. Connect the other lead from a multimeter to contact B of the harness connector for the switch.

  1. Measure the resistance between contact A and contact B. Note the resistance.

  1. Disconnect the lead from contact B and connect the lead to contact C.

  1. Measure the resistance between contact A and contact C.

Expected Result:

The resistance from contact A to contact C is less than 5 ohms, and the resistance from contact A to contact B is greater than 5000 ohms.

Results:

  • OK - The resistance from contact A to contact C is less than 5 ohms, and the resistance from contact A to contact B is greater than 5000 ohms. Proceed to Test Step 4.

  • NOT OK - The resistance measurements do not differ. The switch has failed.

    Repair: Replace the switch.

    STOP

Test Step 4. CHECK THE OPERATION OF THE SWITCH

  1. The machine harness remains disconnected from the switch.

  1. Press and hold the switch.

  1. Connect one lead from a multimeter to contact A of the harness connector for the switch.

  1. Connect the other lead from a multimeter to contact B of the harness connector for the switch.

  1. Measure the resistance between contact A and contact B. Note the resistance.

  1. Disconnect the lead from contact B and connect the lead to contact C.

  1. Measure the resistance between contact A and contact C.

Expected Result:

The resistance from contact A to contact B is less than 5 ohms, and the resistance from contact A to contact C is greater than 5000 ohms.

Results:

  • OK - The resistance from contact A to contact B is less than 5 ohms, and the resistance from contact A and contact C is greater than 5000 ohms. These measurements are opposite of the measurements from the previous Test Step. The switch is operating correctly. Proceed to Test Step 5.

  • NOT OK - The resistance measurements do not differ for both contacts, or the measurements have not changed from the previous Test Step. The switch has failed.

    Repair: Replace the switch.

    STOP

Test Step 5. CHECK IF THE DIAGNOSTIC CODE REMAINS

  1. Inspect the contacts of the harness connectors and clean the connectors.

  1. Reconnect all harness connectors.

  1. Turn the disconnect switch and the key start switch to the ON position.

  1. Operate the machine.

  1. Determine if CID 0070 FMI 04 is present.

Expected Result:

The CID 0070 FMI 04 is active.

Results:

  • YES - The CID 0070 FMI 04 is active. The diagnostic code has not been corrected. The ECM may have failed.

    Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Testing And Adjusting, "Electronic Control Module (ECM) - Replace".

    STOP

  • NO - The CID 0070 FMI 04 is not active. The diagnostic code is NOT present. The diagnostic code does not exist at this time.

    Repair: The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.

    STOP

Information System:

AD55B Underground Articulated Truck Additional Messages
AD55B Underground Articulated Truck Safety Messages
966H Wheel Loader and 972H Wheel Loader Braking and Hydraulic Fan System Pressure Switch (Parking Brake Oil)
D6T Track-Type Tractor Systems Hydraulic Fan Speed (On Demand) - Test and Adjust
Camshaft Lobe Hits Fuel Transfer Pump.{1210, 1256}
953D, 963D and 973D Track-Type Loaders Ripper Does Not Function
953D, 963D and 973D Track-Type Loaders Implement Cycle Time Is Fast
C12 Marine Engines and C12 Power Package Maintenance Recommendations
973D Track-Type Loader Declaration of Conformity
C9.3 Engines for Caterpillar Built Machines Diesel Particulate Filter - Remove and Install
953D, 963D and 973D Track-Type Loaders Hydraulic System Oil Temperature Is High
2009/09/07 Protective Covers For the Joint On the Equalizer Bar Are Now Used {7206}
C3.4B Engines for Caterpillar Built Machines Alternator - Test
953D Track-Type Loader Machine Systems Window Wiper and Wiper Motor
C9.3 Engine and D7E Track-Type Tractors Power Train Oil Cooler - Remove and Install
Piston Seizures on C18 Engines{1225, 1331}
D7E Track-Type Tractor Hydraulic, HVAC, and Electrical Systems Hydraulic System Oil Contains Air
D7E Track-Type Tractor Hydraulic, HVAC, and Electrical Systems Hydraulic System Oil Level Is Low
D7E Track-Type Tractor Hydraulic, HVAC, and Electrical Systems Hydraulic System Oil Temperature Is High
953D, 963D and 973D Track-Type Loaders Steering Does Not Function
953D, 963D and 973D Track-Type Loaders Steering Does Not Function in One Direction
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train MID 081 - CID 0070 - FMI 03
973D Track-Type Loader Machine Systems Window Wiper and Wiper Motor
D6T XE Electrical & Hydraulic Troubleshooting Hydraulic Fan Does Not Function