C9.3 Engines for Caterpillar Built Machines Injector Trim File - Install Caterpillar


Injector Trim File - Install
`

The AVSpare Electronic Technician (ET) is used to load injector trim files into the Engine Control Module (ECM). Injector trim files are available from these sources:

  • A CD-ROM that is packaged with each new injector and each remanufactured injector

  • SIS Web

Replacing an Injector

An injector trim file must be loaded into the ECM if an injector is replaced.

Replacing the ECM

The "Copy Configuration" utility on Cat ET copies the injector trim files between two engine control modules. If the "Copy Configuration" fails, load all of the injector trim files manually into the new ECM.

"Injector Trim" is displayed below a 268-2 or 630-2 Programmed Parameter Fault : Erratic, Intermittent, or Incorrect. The diagnostic code is displayed on Cat ET.

Exchanging Injectors

Exchanging injectors can help determine if a combustion problem is in the injector or in the cylinder. If two injectors that are currently installed in the engine are exchanged between cylinders, the injector trim files can also be exchanged. Press the "Exchange" button at the bottom of the "Injector Trim Calibration" screen on Cat ET. Select the two injectors that have been exchanged and press the "OK" button. The tattletale for the injectors that were exchanged will increase by one.

  1. Perform the following procedure to download an injector trim file from SIS Web. Otherwise, use the injector trim file from the CD-ROM that is packaged with the injector.

      Note: The injector serial number and the injector confirmation code are located on the injector.

    1. Record the injector serial number and the injector confirmation code for each injector.

    2. Click on Service Software Files in SIS Web. Then select "Injector Trim Files".

    3. Enter the serial number for the injector in the search field.

    4. Download the injector trim file to the PC. Repeat this procedure for each injector, as required.

  2. Establish communication between Cat ET and the engine ECM. Refer to Troubleshooting, "Electronic Service Tools", if necessary.

  3. Select the following menu options on Cat ET:

    • Service

    • Calibrations

    • Injector Trim Calibration

  4. Select the appropriate cylinder.

  5. Click on the "Change" button.

  6. Select the appropriate injector trim file from the PC or the CD-ROM.

  7. Click on the "Open" button.

  8. Enter the injector confirmation code.

  9. Click on the "OK" button.

    The injector trim file is loaded into the ECM.

  10. Repeat the procedure for each cylinder, as required.

Information System:

C13 Tier 4 Final Engines General Information - C13 Engines
C9.3 Engines for Caterpillar Built Machines ECM Software - Install
C27 and C32 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install - C32
C9.3 Engines for Caterpillar Built Machines Electrical Connectors - Inspect
D5R Track-Type Tractor Hydraulic System Steering - Calibrate
2009/05/04 A Repair Kit for the Magnet is Now Available for the AccuGrade CD700 Display {7490}
C13 Tier 4 Final Engines Lubrication System
A New Flange Assembly For the Torque Converter On the D10T Is Now Used{3101}
C15 and C18 Industrial Engines Flame Detection Temperature Sensor - Remove and Install - Clean Emissions Module
Installation of VIMS Guardian on Underground Mining Machines{7601}
2009/04/27 Preferred Positions for Mechanically Attached Wear Plates (MAWPS) {6100, 6120, 6820}
2009/07/27 A New Fuel Line Is Now Used on D9T Track-Type Tractors {1274}
Field Installation of the Payload Monitor Gp Kits{7494}
Relocation Of The Expansion Tanks For The Implement Hydraulic System{1354, 5057, 5505}
2009/06/01 A New Bracket Updates the Access Door Group {7251, 7273}
C15 and C18 Industrial Engines Air Inlet Elbow - Remove and Install
2009/05/11 Improved Wiring Harnesses Are Now Available {1408}
C15 and C18 Engines for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Assemble
C13 Tier 4 Final Engines Electronic Control System Components
C13 Engines for Caterpillar Built Machines Combustion Head - Remove and Install - Clean Emissions Module
AccuGrade</SUP> GPS / Single UTS / Site and Laser Reference v11 for Excavators Universal Total Station - MT900
D7E Track-Type Tractor Power Train Track Roller Frame - Remove and Install
Procedure to Align the Dial on the Fuel Sender{1273, 7481, 7857}
C13 Engines for Caterpillar Built Machines Air Control Valve - Remove and Install - ARD Combustion, Clean Emissions Module