Cylinder Head - Inspect
`
3044C Industrial Engine and Engines for Caterpillar Built Machines
[RENR7578]
3044C Industrial Engine and Engines for Caterpillar Built Machines
Gear Group - Inspect
3044C Industrial Engine and Engines for Caterpillar Built Machines
Engine Valve Lash - Inspect/Adjust
BASIC ENGINE
CYLINDER HEAD GP
3044C Industrial Engine and Engines for Caterpillar Built Machines
Cylinder Head - Inspect
3044C Industrial Engine and Engines for Caterpillar Built Machines
Engine Valve Lash - Inspect/Adjust
3044C Industrial Engine and Engines for Caterpillar Built Machines
Fuel Injection Nozzle - Test
Show/hide table
Required Tools     | ||
Part Number     | Part Name     | Qty     |
8S-6691     | Cylinder Head Repair Stand     | 1     |
8H-8581     | Feeler Gauge     | 1     |
- Remove the cylinder head from the engine.
- Clean the cylinder head thoroughly. Make sure that the contact surfaces of the cylinder head and the cylinder block are clean, smooth and flat.
- Inspect the bottom surface of the cylinder head for pitting, corrosion, and cracks. Inspect the area around the valve seat inserts and the holes for the fuel injection nozzles.
- Place cylinder head (1) on cylinder head repair stand (2) .
Show/hide table
![]() | |
Illustration 1 | g00876690 |
Typical example (1) Cylinder head (2) Cylinder head repair stand |
- Measure the cylinder head for flatness. Measure the flatness with straight edge (3) and with feeler gauge (4) .
- Measure the cylinder head from one side to the other side (A) .
- Measure the cylinder head from one end to the other end (B) .
- Measure the cylinder head from one corner to the other corner (C) .
Refer to Specifications, "Cylinder Head" for the requirements of flatness.
- Measure the cylinder head from one side to the other side (A) .
Show/hide table
![]() | |
Illustration 2 | g00987700 |
Measuring points on cylinder head (A) Side to side (B) End to end (C) Corner to corner |
Show/hide table
![]() | |
Illustration 3 | g00987701 |
Measuring flatness (3) Straight edge (4) Feeler gauge |
Information System:
D11R Track-Type Tractor
Engine Valve Lash - Check/Adjust
3044C Industrial Engine and Engines for Caterpillar Built Machines
Gear Group - Inspect
2003/04/21
Correction to Parts Manuals , "175-3094 Clutch and Gear Group (Third and Fourth)" {3061, 3155}
2003/03/24
Correction to Disassembly and Assembly , "Transmission - Assemble" {1408, 3030, 3030}
3046 Engine for Caterpillar Built Machines
Flywheel - Inspect
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Engine Supplement
Crankshaft Front Seal - Remove
C4.4 Industrial Engine
Engine Oil Pump - Inspect
3044C Industrial Engine and Engines for Caterpillar Built Machines
Cylinder Block
2003/03/31
Correction to Specifications , "Steering Control Valve" {4307}
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Engine Supplement
Refrigerant Compressor - Remove and Install
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Engine Supplement
Alternator - Remove and Install
AD30 Underground Articulated Truck Hydraulic System
Oil Filter (Pilot)
C-9 Engine for Caterpillar Built Machines
Diagnostic Codes
D6N Track-Type Tractor Machine Systems
Battery - Remove and Install
3046 Engine for Caterpillar Built Machines
Connecting Rod - Inspect
3044C Industrial Engine and Engines for Caterpillar Built Machines
Crankshaft
980G Wheel Loader Power Train
Torque Converter - Disassemble - Heavy Duty
Replacement of Implement Pump with Gear Pump{5055, 5084}
D6N Track-Type Tractor Machine Systems
Bottom Guard - Remove
D6N Track-Type Tractor Machine Systems
Bottom Guard - Install
938G Wheel Loader and IT38G Integrated Toolcarrier
Safety Messages
2003/03/24
Special Instruction, REHS1578, "Installation Instructions for the 9W-1494 Service Meter Kit " Is Available {7478}
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Engine Supplement
Crankshaft Front Seal - Install
AD30 Underground Articulated Truck Braking System
Service and Parking Brake