Finding Top Center Position for No. 1 Piston
`
C7.1 Industrial Engine
[UENR0666]
C7.1 Industrial Engine
Engine Oil Pump - Inspect
C7.1 Industrial Engine
Air Inlet and Exhaust System - Inspect
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A (1)     | 9U-6198     | Crankshaft Turning Tool     | 1     |
A (2)     | 5P-7306     | Housing     | 1     |
5P-7305 | Engine Turning Tool     | 1     | |
B     | 230-6284     | Timing Pin (Camshaft)     | 1     |
C     | 136-4632     | Timing Pin (Crankshaft)     | 1     |
268-1966 | Adaptor     | 1     |
Show/hide table
( 1 ) | The Crankshaft Turning Tool is used on the front pulley. |
( 2 ) | This Tool is used in the aperture for the electric starting motor. |
Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
- Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install".
- Use Tooling (A) in order to rotate the crankshaft until the Hole (X) in the camshaft gear (1) aligns with the hole in the front housing. Refer to illustration 1. Remove the plug (2) from the cylinder block. Install Tooling (C) into the Hole (Y) in the cylinder block. Use Tooling (C) in order to lock the crankshaft in the correct position.
Note: Do not use excessive force to install Tooling (C) . Do not use Tooling (C) to hold the crankshaft during repairs.
Show/hide table
![]() | |
Illustration 1 | g01907734 |
Typical example |
Show/hide table
![]() | |
Illustration 2 | g01907735 |
Typical example |
- Install Tooling (B) through the hole (X) in the camshaft gear (1) into the front housing. Use Tooling (B) in order to lock the camshaft in the correct position.
Information System:
C7.1 Industrial Engine
Engine Oil Pump - Inspect
C4.4 Industrial Engine
Cooling System - Test
C7.1 Engines for Caterpillar Built Machines
Vibration Damper - Check
C4.4 Industrial Engine
Flywheel - Inspect
C7.1 Industrial Engine
Cylinder Head - Inspect
C7.1 Industrial Engine
Connecting Rod - Inspect
C7.1 Industrial Engine
Engine Oil Cooler - Inspect
C4.4 Industrial Engine
Cooling System Coolant Level - Check
C4.4 Industrial Engine
Valve Depth - Inspect
C4.4 Industrial Engine
Compression - Test
C7.1 Industrial Engine
Fuel Injection Timing - Check
C4.4 Industrial Engine
Air in Fuel - Test
C7.1 Industrial Engine
Basic Engine
C7.1 Industrial Engine
Cooling System
C7.1 Engines for Caterpillar Built Machines
Electrical System
C7.1 Industrial Engine
Fuel Injection
C7.1 Industrial Engine
Power Sources
C4.4 Industrial Engine
Turbocharger - Inspect - Series Turbochargers
Installation of 6SU (S/N: D1Y; S6A) Bulldozer{5102, 6050, 6078}
D6R Series III, D6T and D7R Series II Track-Type Tractors
MID 113 - CID 0623 - FMI 02
C15 and C18 Tier 4 Final Engines
Fuel System
C13 Tier 4 Final Engines
Cooling System
C11, C13, C15, and C18 Industrial Engines
Component Location
C7.1 Engines for Caterpillar Built Machines
Alternator - Test