973D Track-Type Loader Power Train Track Roller Caterpillar


Track Roller
`
1.1. Single Flange Track Roller
2.1. Double Flange Track Roller



Illustration 1g01947017

The machines have four double flange rollers (1) and three single flange track rollers (2). The track rollers are fastened to the roller frames. The track rollers are in contact with the surfaces of the track links. The flanges on the track rollers prevent movement of the track from side to side. The inside surfaces of the track links equally distribute the weight of the machine over the track.

Single Flange Track Roller




Illustration 2g01947077

The single flange track roller is shown.

(3) Shaft

(4) Collar

(5) Duo-Cone seals

Collars (4) get the side load on the roller. The amount of side movement or the end clearance of shaft (3) cannot be adjusted.

The track rollers have Duo-Cone seals (5) at both ends of shaft (1) .

The center of shaft (3) is an oil reservoir. This oil is used for lubrication of the bearing surfaces.

Double Flange Track Roller




Illustration 3g01947067

The double flange track roller is shown.

(3) Shaft

(4) Collar

(5) Duo-Cone seals

Collars (4) get the side load on the roller. The amount of side movement or the end clearance of shaft (3) cannot be adjusted.

The track rollers have Duo-Cone seals (5) at both ends of shaft (3) .

The center of shaft (3) is an oil reservoir. This oil is used for lubrication of the bearing surfaces.

Information System:

C4.4 Industrial Engine Refrigerant Compressor
2009/06/29 An Improved Adjustable Armrest Is Now Available {7307}
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735B, 735C, 740B, 740B Ejector, 740C Ejector and 745C Articulated Trucks VIMSTM</SUP> 3G Using Caterpillar Electronic Technician to Determine Diagnostic Codes
973D Track-Type Loader Power Train General Information
2009/07/06 The Undercarriage Has Been Changed To Camber Only {4150}
973D Track-Type Loader Hydraulic System Location of Electrical Components
2009/08/10 An Improved Engine Oil Pump Assembly Is Used {1304}
Procedure To Rework the Torque Converter and Updrive Housing Speed Sensor Mount{3101, 3159, 3175}
D6K Track-Type Tractor Machine Systems Pump Mounting - Remove and Install
C13, C15, and C18 Tier 4 Interim Engines ARD Ignition - Test
2009/06/22 New AccuGrade Version 11.10 Software is Now Available {7220, 7620}
Procedure For Retrofitting The D6K Track-Type Tractor With The AccuGrade</SUP> Harness{7220}
Generator Bearing Service {4457}
966H and 972H Wheel Loaders Machine Systems Lubrication Pump (Automatic) - Assemble
966H and 972H Wheel Loaders Machine Systems Lubrication Pump (Automatic) - Disassemble
973D Track-Type Loader Power Train Hydrostatic Drive Motor
C6.6 Industrial Engine Exhaust Gas Valve (NRS)
2009/06/29 Improvements to the Lines Group for the Lift Cylinder on 938H and IT38H Machines {5057, 5102}
C9.3 Engines for Caterpillar Built Machines Engine Control Module - Remove and Install
973D Track-Type Loader Power Train Location of Electrical Components
973 K Track-Type Loaders Equalizer Bar
973 K Track-Type Loaders Front Idler and Recoil Spring
3500 Engines Prelubrication Oil Pump - Remove and Install
3500 Engines Electronic Control Module (Engine) - Remove and Install