973D Track-Type Loader Hydraulic System General Information Caterpillar


General Information
`
1.1. Implement Hydraulic System
2.1. Implement Schematic

Implement Hydraulic System

The implement hydraulic system controls the operation of the track loader. The pumps are mounted directly to the flywheel housing. The implement pumps supply oil to the hydraulic cylinders for the loader bucket, the ripper (if equipped), and the multipurpose bucket (if equipped). The right charge pump provides charge pressure to the right hystat pump and pilot pressure to the load sensing circuit for the implement control valves.

Implement Schematic




Illustration 1g01926813

HOLD

(A) Inlet manifold

(B) Bucket lift control section

(C) Bucket tilt control section

(D) Multipurpose bucket control section

(E) Ripper lift control section

(F) Outlet manifold

(1) Dead electronic lower valve (Ripper circuit)

(2) Dead electronic lower valve (Lift circuit)

(3) Bucket lift control valve

(4) Lift cylinders

(5) Makeup valve (lift rod end)

(6) Line relief valve (lift head end)

(7) Bucket tilt control valve

(8) Tilt cylinder

(9) Line relief valve (tilt rod end)

(10) Line relief valve (tilt head end)

(11) Anti-drift valve

(12) Multipurpose bucket control valve

(13) Multipurpose bucket cylinders

(14) Line relief valve (multipurpose bucket rod end)

(15) Line relief valve (multipurpose bucket head end)

(16) Ripper cylinder

(17) Line relief valve (ripper)

(18) Pilot shut-off valve

(19) Accumulator

(20) Flow from the charge circuit of the right drive pump

(21) Pressure reducing valve

(22) Margin relief valve

(23) Ripper control valve

(24) Pilot control solenoid

(25) Implement pump compensator valves

(26) Implement pumps

(27) Hydraulic oil tank

(28) Drain

(29) Temperature sensor

(30) Hydraulic tank breather

(31) Return line back pressure

(32) Load sensing relief valve

(33) Signal duplicating reducing valve

Information System:

D7E Track-Type Tractor Lifting and Tying Down the Machine
988G Wheel Loader Power Train Torque Converter (Lockup) - Assemble - Type 2
D6T Track-Type Tractor Hydraulic System Piston Pump (Steering)
C9.3 Engines for Caterpillar Built Machines Relief Valve (Fuel) - Remove and Install
C9.3 Engines for Caterpillar Built Machines Fuel Manifold (Rail) - Remove and Install
D6T Track-Type Tractor Hydraulic System Piston Pump (Implement)
3500B Engines for Caterpillar Built Power Modules Fuel Injector Mechanism
973D Track-Type Loader Machine Systems Fuel Tank
988G Wheel Loader Electrohydraulic System MID 082 - CID 1964 - FMI 08
D6T Track-Type Tractor Systems Hydraulic Tank and Filter
2009/06/22 Improvements Have Been Made to the Lift Cylinder {5102}
988G Wheel Loader Power Train Torque Converter (Lockup) - Disassemble - Type 2
3500B Engines Air Shutoff
C9.3 Engines for Caterpillar Built Machines Fuel Manifold - Remove and Install - Return
CUSTOM SERVICE INFORMATION for the 980H UNDERGROUND MINE AR {1050, 1051, 4250, 4267, 4300, 4307, 4330, 5050, 5109, 5112, 5134, 7000}
2009/06/15 New Software Is Now Used For Elevated Idle {1901, 1902, 1920}
973D Track-Type Loader Monitoring System
C13 Engines for Caterpillar Built Machines Fuel System - Prime
C13 Engines for Caterpillar Built Machines Fuel System Pressure - Test
D7E Track-Type Tractor Declaration of Conformity
2009/06/15 New Sensors Are Now Available For the Implement Control Lever On Certain Track-Type Tractors {5737}
2009/09/07 Protective Covers For the Joint On the Equalizer Bar Are Now Used {7206}
973D Track-Type Loader Hydraulic System Tilt Circuit
2009/06/15 The Engine Enclosure May Need to Be Updated {7267, 7276}