Bucket Control Group
`
953C Track-Type Loader Hydraulic System
[RENR5650]
953C Track-Type Loader Hydraulic System
Pilot Valve
953C Track-Type Loader Hydraulic System
Accumulator - Test
IMPLEMENTS
CONTROL GP
953C Track-Type Loader Hydraulic System
Bucket Control Group
1.1. Installation Procedure for Pin Assemblies
Show/hide table
 | |
| Illustration 1 | g00998986 |
Show/hide table
| Linkage Pins | |||||
|---|---|---|---|---|---|
| Pin Number | Pin Location | Pin Diameter | Pin Length | Part Number of Assembly | Part Number of Pin |
| (1) | Lift arms to main frame | 76.18 ± 0.02 mm (2.999 ± 0.001 inch) |
282.0 ± 1.5 mm (11.10 ± 0.06 inch) |
8G-1096 | 7P-3469 |
| (2) | Tilt cylinder to main frame | 82.53 mm (3.249 inch) |
203.0 ± 3.0 mm (7.99 ± 0.12 inch) |
232-1702 | 232-1701 |
| (3) | Tilt cylinder to lever | 82.53 mm (3.249 inch) |
249.0 ± 1.5 mm (9.80 ± 0.06 inch) |
8G-1099 | 7P-3476 |
| (4) | Lever to lift arms | 101.575 mm (3.9990 inch) |
341.0 ± 3.0 mm (13.43 ± 0.12 inch) |
7P-3467 | 7P-3468 |
| (5) | Lift cylinder to main frame | 63.48 mm (2.499 inch) |
236.0 ± 1.5 mm (9.29 ± 0.06 inch) |
8G-1097 | 7P-3471 |
| (6) | Lift cylinder to lift arms | 63.48 mm (2.499 inch) |
169.0 ± 1.5 mm (6.655 ± 0.06 inch) |
8G-1098 | 7P-3470 |
| (7) | Lever to link | 69.83 mm (2.749 inch) |
249.0 ± 1.5 mm (9.80 ± 0.06 inch) |
8G-1105 | 7P-3473 |
| (8) | Link to bucket | 69.83 mm (2.749 inch) |
224.0 ± 3.0 mm (8.82 ± 0.12 inch) |
8G-8331 | 8G-8332 |
| (9) | Lift arms to bucket | 57.112 mm (2.2485 inch) |
258.0 ± 3.0 mm (10.16 ± 0.12 inch) |
8G-4027 | 8G-4028 |
Show/hide table
| Linkage Bearings | ||||
|---|---|---|---|---|
| Number for Bearing | Location of Bearing | Inside Diameter before Assembly | Depth at Assembly | Part Number |
| (10) | Lift arms | 76.481 ± 0.020 mm (3.0111 ± 0.0008 inch) |
10.0 ± 0.069 mm (0.39 ± 0.0027 inch) |
7P-3453 |
| (11) | Head end of tilt cylinder | 82.84 ± 0.020 mm (3.261 ± 0.001 inch) |
8.4 ± 3.0 mm (0.33 ± 0.12 inch) |
3G-5111 |
| (12) | Rod end of tilt cylinder | 82.84 ± 0.020 mm (3.261 ± 0.001 inch) |
8.4 ± 3.0 mm (0.33 ± 0.12 inch) |
3G-5111 |
| (13) | Lever | 101.91 ± 0.020 mm (4.012 ± 0.001 inch) |
10.0 ± 1.0 mm (0.39 ± 0.04 inch) |
7P-3463 |
| (14) | Head end of lift cylinder | 63.77 ± 0.020 mm (2.511 ± 0.001 inch) |
9.4 ± 0.5 mm (0.37 ± 0.02 inch) |
1U-0563 |
| (15) | Lift arms | 63.741 ± 0.020 mm (2.5095 ± 0.0008 inch) |
10.0 ± 1.0 mm (0.39 ± 0.04 inch) |
7P-3454 |
| (16) | Link | 70.102 ± 0.020 mm (2.7599 ± 0.0008 inch) |
10.0 ± 1.0 mm (0.39 ± 0.04 inch) |
7P-3466 |
| (17) | Link | 70.102 ± 0.020 mm (2.7599 ± 0.0008 inch) |
10.0 ± 1.0 mm (0.39 ± 0.04 inch) |
7P-3466 |
| (18) | Lift arms (inside diameter of sleeve bearing) | 57.379 ± 0.020 mm (2.2590 ± 0.0008 inch) |
9.0 ± 1.0 mm (0.35 ± 0.04 inch) |
8G-4022 |
| Lift arms (outside diameter of sleeve bearing) | 69.895 ± 0.013 mm (2.7518 ± 0.0005 inch) |
|||
Note: Put lubricant on the lip of all seals. Apply lubricant from the 5P-0960 Grease Cartridge onto all pin bores (lift cylinders, tilt cylinders, bucket and frame).
Installation Procedure for Pin Assemblies
- Clean the bores for all pin assemblies.
- Install pin assemblies through the lift arm assembly and the bucket.
- Install a minimum of one washer on each side of arm. Install additional washers in order to achieve a maximum clearance of 1.8 mm (0.071 inch).
Information System:
3044C Industrial Engine and Engines for Caterpillar Built Machines
Exhaust Manifold - Remove and Install
963C Track-Type Loader
Maintenance Interval Schedule
613C Series II Wheel Tractor Power Train
Transmission and Transfer Gears - Remove
3044C Industrial Engine and Engines for Caterpillar Built Machines
Fuel Injection Lines - Remove and Install - Naturally Aspirated Engines
953C Track-Type Loader Hydraulic System
Pilot Valve
615C Series II Wheel Tractor-Scraper Wheel Tractor Power Train
Leading Arm - Install
963C Track-Type Loader Power Train
Hydraulic Drive Pump - Assemble
963C Track-Type Loader Power Train
Hydraulic Drive Pump - Disassemble
615C Series II Wheel Tractor-Scraper Wheel Tractor Power Train
Leading Arm - Remove
980G Series II Wheel Loader
Operation Information
953C, 963C and 973C Track-Type Loaders Transmission Electronic Control System
E703 High Right Track Steering Pressure
953C, 963C and 973C Track-Type Loaders Transmission Electronic Control System
E702 High Left Track Steering Pressure
TH220B, TH330B and TH340B Telehandlers
Transmission and Hydraulic System Oil Level - Check
613C Series II Wheel Tractor Power Train
Transmission and Transfer Gears - Install
3044C Industrial Engine and Engines for Caterpillar Built Machines
Engine Oil Filter Base - Remove and Install
980G Series II Wheel Loader Power Train
Transmission Pressures - Test and Adjust
613C Series II Wheel Tractor Power Train
Torque Converter - Remove
2003/05/12
Correction to Testing and Adjusting , "Transmission Pressures - Test and Adjust" {3081}
2003/05/19
Correction to Testing and Adjusting , "Ride Control Accumulator Recharging Procedure" {5077}
613C Series II Wheel Tractor Power Train
Torque Converter - Install
3044C Industrial Engine and Engines for Caterpillar Built Machines
Engine Oil Relief Valve - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines
Water Pump - Remove and Install
613C Series II Wheel Tractor Power Train
Torque Converter - Disassemble
3044C Industrial Engine and Engines for Caterpillar Built Machines
Water Temperature Regulator Housing - Remove and Install