966G Series II Wheel Loader and 972G Series II Wheel Loader Hydraulic System Tilt Cylinder - High Lift Caterpillar


Tilt Cylinder - High Lift
`
966G Series II Wheel Loader and 972G Series II <BR>Wheel Loader Hydraulic System [RENR4394]
HYDRAULIC SYSTEM
CYLINDER GP
966G Series II Wheel Loader and 972G Series II Wheel Loader Hydraulic System Tilt Cylinder
966G Series II Wheel Loader and 972G Series II Wheel Loader Hydraulic System Tilt Cylinder - High Lift
1.1. 171-3953 Tilt Cylinder
2.1. 190-5955 Tilt Cylinder



Illustration 1g00989728

171-3953 Tilt Cylinder

(1) Lubricate the threads before assembly. Tighten the nut to the following torque. ... 6500 ± 650 N·m (4800 ± 480 lb ft)

(2) Outside diameter of the piston in two places ... 208.55 ± 0.03 mm (8.2106 ± 0.0012 inch)

(3) Inside diameter of the cylinder bore ... 209.6 ± 0.1 mm (8.2520 ± 0.0039 inch)

(4) Diameter of a new cylinder rod ... 82.50 ± 0.038 mm (3.2480 ± 0.0015 inch)

(5) Inside diameter of the two lands in the cylinder head ... 83.00 ± 0.13 mm (3.2677 ± 0.0051 inch)

(6) Tighten the eight bolts to the following torque. ... 900 ± 100 N·m (665 ± 75 lb ft)

(7) Lubricate the seals with the lubricant that is being sealed.

(8) Apply 4C-4032 Bearing Mount Compound to the wiper seal groove before installation.

Pin to pin length of a retracted cylinder ... 1245 mm (49 inch)

Cylinder stroke ... 550 mm (21.7 inch)

190-5955 Tilt Cylinder

(1) Lubricate the threads before assembly. Tighten the nut to the following torque. ... 8100 ± 810 N·m (6000 ± 600 lb ft)

(2) Outside diameter of the piston in two places ... 233.93 ± 0.03 mm (9.2098 ± 0.0012 inch)

(3) Inside diameter of the cylinder bore ... 235.0 ± 0.1 mm (9.2520 ± 0.0039 inch)

(4) Diameter of a new cylinder rod ... 88.9 mm (3.5000 inch)

(5) Inside diameter of the four lands in the cylinder head ... 89.18 ± 0.03 mm (3.5110 ± 0.0012 inch)

(6) Tighten the eight bolts to the following torque. ... 900 ± 100 N·m (665 ± 75 lb ft)

(7) Lubricate the seals with the lubricant that is being sealed.

Pin to pin length of a retracted cylinder ... 1245 mm (49 inch)

Cylinder stroke ... 550 mm (21.7 inch)

Information System:

C7 Engines for Caterpillar Built Machines Camshaft Idler Gear - Remove and Install
C15 and C18 Generator Set Engines Pistons and Connecting Rods - Install
C15 and C18 Generator Set Engines Connecting Rod Bearings - Remove
C15 On-Highway Engine Crankshaft - Install
C15 and C18 Generator Set Engines Pistons and Connecting Rods - Disassemble
C15 On-Highway Engine Pistons and Connecting Rods - Assemble
C15 On-Highway Engine Camshaft - Remove
C15 On-Highway Engine Camshaft - Install
C15 and C18 Generator Set Engines Connecting Rod Bearings - Install
C15 and C18 Generator Set Engines Crankshaft Main Bearings - Remove
C15 On-Highway Engine Crankshaft - Remove
C15 and C18 Generator Set Engines Crankshaft Main Bearings - Install
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Differential and Final Drive Oil Sample - Obtain
Installation Instructions for the 2Q-8564 Ride Control Gp (KIT){5004, 5004}
C7 Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
966G Series II Wheel Loader and 972G Series II Wheel Loader Hydraulic System Relief Valve
Installation of Product Link{7602}
966G Series II Wheel Loader and 972G Series II Wheel Loader Hydraulic System Electrohydraulic Control
2003/11/17 Changes to the Mounting Hardware Improve the Service Life of the Rear Frame {7051}
966G Series II Wheel Loader and 972G Series II Wheel Loader Hydraulic System Pilot Operated Hydraulic Control
AD30 Underground Articulated Truck Transmission Oil - Change
AD30 Underground Articulated Truck Transmission Oil Filter - Replace
966G Series II Wheel Loader and 972G Series II Wheel Loader Hydraulic System Implement System - Electrohydraulic System
966G Series II Wheel Loader and 972G Series II Wheel Loader Hydraulic System Implement System - Pilot Hydraulics