Cylinder Head
`
3508B Engine for Caterpillar Built Machines
[RENR1308]
3508B Engine for Caterpillar Built Machines
Fuel Injector Mechanism
3508B Engine for Caterpillar Built Machines
Air Inlet and Exhaust Lines
BASIC ENGINE
CYLINDER HEAD GP
3508B Engine for Caterpillar Built Machines
Cylinder Head
3508B Engine for Caterpillar Built Machines
Cylinder Head Valves
Show/hide table
| |
| Illustration 1 | g06341337 |
Show/hide table
| Specifications for 7E-8758 Cylinder Head Gp, 203-2169 Cylinder Head Gp, 203-2170 Cylinder Head Gp, 242-5326 Cylinder Head As and 350-5202 Cylinder Head Gp | |||
|---|---|---|---|
| Item | Qty | Part | Specification Description |
| 1 | 2 | 130-2607 Valve Seat Insert | During installation, shrink the valve seat insert with reduced temperature (Reference temperature: |
| 2 | 2 | 130-2608 Valve Seat Insert | During installation, shrink the valve seat insert with reduced temperature (Reference temperature: |
| 3 | 5 | 3B-0645 Cup Plug | Before assembly, apply high strength or high temperature Anaerobic Flange sealant to the bores. |
| 4 | 1 | 3B-0623 Cup Plug | Before assembly, apply high strength or high temperature Anaerobic Flange sealant to the bores. |
| 5 | 2 | 3B-0623 Cup Plug | Before assembly, apply high strength or high temperature Anaerobic Flange sealant to the bores. Installation depth (E) is |
| 6 | 2 | 3B-0623 Cup Plug | Before assembly, apply high strength or high temperature Anaerobic Flange sealant to the bores. Installation depth (D) is |
Show/hide table
| |
| Illustration 2 | g06341342 |
Show/hide table
| Bolt Tightening Procedure with the 110-6991 Cylinder Head Gasket | |||
|---|---|---|---|
| Item | Qty | Part | Specification Description |
| Note: Bolt Tightening Procedure with the 110-6991 Cylinder Head Gasket (Cellulose) and 110-6994 Spacer Plate (Aluminum) or 362-9677 Spacer Plate (Aluminum). | |||
| 7 | 6 | 131-0420 Cylinder Head Fastener Gp |
Use the following procedure in order to tighten the bolts for the cylinder head: Refer to Illustration 2 for bolt tightening sequence. 1. Before assembly, apply clean engine oil to the bolt threads. 2. Tighten bolt 1 through 8 in the numerical sequence to 3. Again, retighten bolts 1 through 8 in the numerical sequence to 4. Again, retighten bolts 1 through 8 in numerical sequence to 5. Turn bolt 1 through 8 in numerical sequence to an angle of 180 ± 5 degrees. Note: Tighten bolts 9 only after bolts 1 through 8 have been turned 180 ± 5 degrees. 6. Tighten bolts (9) to |
| 8 | 2 | 131-0421 Cylinder Head Fastener Gp |
|
| 9 | 2 | 5B-0213 Bolt |
|
Show/hide table
| |
| Illustration 3 | g06341366 |
Show/hide table
| Bolt Tightening Procedure with the 362-8264 Cylinder Head Gasket | |||
| Item | Qty | Part | Specification Description |
| Note: Bolt Tightening Procedure with the 362-8264 Cylinder Head Gasket (MLS) and 519-7297 Spacer Plate (Iron).
Note: Refer to Disassembly and assembly manual for the alternate tightening procedure of cylinder head using 362-8264 Cylinder Head Gasket (MLS) with 110-6994 Spacer Plate (Aluminum) or 362-9677 Spacer Plate (Aluminum). |
|||
| 7 | 6 | 131-0420 Cylinder Head Fastener Gp |
Use the following procedure in order to tighten the bolts for the cylinder head: Refer to Illustration 3 for bolt tightening sequence. 1. Before assembly, apply clean engine oil to the bolt threads. 2. Tighten bolt 1 through 8 in the numerical sequence to 3. Again, retighten bolts 1 through 8 in the numerical sequence to 4. Again, retighten bolts 1 through 8 in the numerical sequence to 5. Turn bolts 1 through 8 in the numerical sequence to an angle of 180 ± 5 degrees. Note: Tighten bolts 9 only after bolts 1 through 8 have been given the final torque. 7. Tighten bolts 9 to |
| 8 | 2 | 131-0421 Cylinder Head Fastener Gp |
|
| 9 | 2 | 5B-0213 Bolt |
|
Information System:
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors
Battery Electrolyte Level - Check
3500B Engines for Caterpillar Built Power Modules
Camshaft
3500B Engines for Caterpillar Built Power Modules
Valve Mechanism
3500B Engines for Caterpillar Built Power Modules
Fuel Injector
D11R Track-Type Tractor
After Starting Engine
3508B Engine for Caterpillar Built Machines
Fuel Injector Mechanism
3500B Engines for Caterpillar Built Power Modules
Fuel Transfer Pump
992G Wheel Loader and 854G Wheel Dozer Power Train
Axle Oil Cooler
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors
Starting with Auxiliary Start Receptacle
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors
Fuel System Primary Filter - Replace
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors
Engine Oil and Filter - Change
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors
Starting with Jump Start Cables
3508B Engine for Caterpillar Built Machines
Air Inlet and Exhaust Lines
980G Wheel Loader
Sound Information and Vibration Information
143H and 163H Motor Graders
Tire Inflation with Nitrogen
980G Wheel Loader
Plate Locations and Film Locations
980G Wheel Loader
Battery Disconnect Switch
980G Wheel Loader
Warning Categories (Caterpillar Monitoring System)
966G and 972G Wheel Loaders
Light Switches
3500B Engines for Caterpillar Built Power Modules
Crankshaft Wear Sleeves and Seals
966G and 972G Wheel Loaders
Window Wiper and Washer Control
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors
Seat
3500B Engines for Caterpillar Built Power Modules
Housing (Front)
D6M Track-Type Tractor
Bulldozer Blade Tip