950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Hydraulic System Bucket Control Group Caterpillar


Bucket Control Group
`
950G Wheel Loader, 962G <BR>Wheel Loader and IT62G <BR>Integrated Toolcarrier Hydraulic System [SENR1388]
IMPLEMENTS
CONTROL GP
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Hydraulic System Bucket Control Group
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Hydraulic System Implement Control Group



Illustration 1g00459609

Bucket Control Group

(1) Torque for the five bolts ... 460 ± 60 N·m (340 ± 45 lb ft)




Illustration 2g00459742

Section View of Pins

Table 1
Linkage Pins and Bolts    
View     Pin     Part Number of Pin Assembly     Part Number of Pin     Pin Diameter     Pin Length at Assembly     Bolt     Bolt Torque    
A-A     2     136-9371     136-9378    
88.86 ± 0.04 mm (3.498 ± .002 inch)    

297 ± 3 mm (11.7 ± .1 inch)    
12    
460 ± 60 N·m (340 ± 45 lb ft)    
B-B     5     136-9380     136-9383    
88.86 ± 0.04 mm (3.498 ± .002 inch)    

277 ± 3 mm (10.9 ± .1 inch)    
13    
460 ± 60 N·m (340 ± 45 lb ft)    
C-C     7     5V-1508     5V-1507    
82.53 ± 0.03 mm (3.249 ± .001 inch)    

213 ± 3 mm (8.4 ± .1 inch)    
6    
460 ± 60 N·m (340 ± 45 lb ft)    
D-D     14     136-9371     136-9378    
88.86 ± 0.04 mm (3.498 ± .002 inch)    

297 ± 3 mm (11.7 ± .1 inch)    
20    
460 ± 60 N·m (340 ± 45 lb ft)    
E-E     22     4E-3196     4E-3198    
76.18 ± 0.03 mm (2.999 ± .001 inch)    

198 ± 3 mm (7.8 ± .1 inch)    
-     -    
F-F     23     9C-0093     9C-0094    
114.26 ± 0.04 mm (4.498 ± .002 inch)    

315 ± 3 mm (12.4 ± .1 inch)    
19    
460 ± 60 N·m (340 ± 45 lb ft)    
G-G     25     5V-1508     5V-1507    
82.53 ± 0.03 mm (3.249 ± .001 inch)    

213 ± 3 mm (8.4 ± .1 inch)    
26    
460 ± 60 N·m (340 ± 45 lb ft)    
H-H     28     5V-1882     5V-1881    
82.53 ± 0.03 mm (3.249 ± .001 inch)    

195 ± 3 mm (7.7 ± .1 inch)    
-     -    
J-J     30     5V-1511     5V-1512    
63.48 ± 0.03 mm (2.499 ± .001 inch)    

232 ± 3 mm (9.1 ± .1 inch)    
-     -    

Table 2
Linkage Bearings and Seals    
View     Bearing     Part Number of Bearing     Inside Diameter of Bearing     Bearing Depth at Assembly     Seal     Part Number of Seal    
A-A     3     3V-2333    
89.19 ± 0.02 mm (3.511 ± .001 inch)    

10.0 ± 1.0 mm (.39 ± .04 inch)    
4     7K-9212    
E-E     21     4V-8674    
76.48 ± 0.02 mm (3.011 ± .001 inch)    

9.5 ± 1.0 mm (.37 ± .04 inch)    
17     7K-9209    
F-F     24     5V-1386    
114.62 ± 0.02 mm (4.513 ± .001 inch)    

10.0 ± 1.0 mm (.39 ± .04 inch)    
18     7K-9218    
G-G     31     3G-8779    
82.84 ± 0.02 mm (3.261 ± .001 inch)    

9.5 ± 1.0 mm (.37 ± .04 inch)    
32     7K-9210    
H-H     27     3G-8779    
82.84 ± 0.02 mm (3.261 ± .001 inch)    

9.5 ± 1.0 mm (.37 ± .04 inch)    
33     7K-9210    
J-J     35     5V-1874    
63.74 ± 0.02 mm (2.509 ± .001 inch)    

10.0 ± 1.0 mm (.39 ± .04 inch)    
34     7K-9205    

Note: Coat all of the pin bores with 5P-0960 Molybdenum Grease prior to assembly.

(8) 159-0269 Shim

Thickness of one shim ... 2 mm (.08 inch)

(9) Install the washers in order to center the lift arm on the frame. Maximum distance between the lift arm and the frame ... 2.0 mm (.08 inch)

(10) 159-0268 Shim

Thickness of one shim ... 1 mm (.04 inch)

(11) Install the washers in order to center the lift arm on the frame. Maximum distance between the lift arm and the frame ... 2.0 mm (.08 inch)

(15) 159-0269 Shim

Thickness of one shim ... 2 mm (.08 inch)

(16) Lubricate all 18 sealing lips with the lubricant that is being sealed.

(29) Install washers at the interface of the lift arm and the bucket in order to provide a wear surface. Use a minimum of one washer at each wear surface.