3208 Marine Engine Hose Clamps Caterpillar


Hose Clamps
`

Worm Drive Band Type Clamps



Illustration 1g00910017

Table 1
Width (A) of Clamp  Torque for New Hose 
7.5 mm (0.3 inch) or greater  1.4 ± 0.3 N·m (12 ± 3 lb in) 
12 mm (0.5 inch) or greater  4.5 ± 0.7 N·m (40 ± 6 lb in) 
14 mm (0.6 inch) or greater  7.5 ± 1 N·m (66 ± 9 lb in) 
Width (A) of Clamp  Torque for Reused Hose(1) 
7.5 mm (0.3 inch) or greater  0.8 ± 0.3 N·m (7 ± 3 lb in) 
12 mm (0.5 inch) or greater  3.0 ± 0.5 N·m (27 ± 4 lb in) 
14 mm (0.6 inch) or greater  4.5 ± 0.7 N·m (40 ± 6 lb in) 
(1) Use this value when the hose is reused. The clamp may be new or reused.

Constant Torque Hose Clamps

Use a constant torque hose clamp in place of any worm drive band type clamp. Ensure that the constant torque hose clamp is the same size as the worm drive band type clamp. Due to extreme temperature changes, the hose will heat set. Heat setting can cause worm drive band type clamps to loosen. Loose hose clamps can result in leaks. There have been reports of component failures that have been caused by worm drive band type clamps that have loosened. The constant torque hose clamp will help prevent these failures.



Illustration 2g03076961
(1) Constant Torque Hose Clamp (Belleville Washer)
(2) Constant Torque Hose Clamp (Tee bolt and Spring)

Use a torque wrench for proper installation of all constant torque hose clamps. There are two types of constant torque hose clamps: Belleville washer (1) and Tee bolt and spring (2)

When the constant torque hose clamp (Belleville washer) (1) is assembled correctly, the Belleville washers (1A) are nearly collapsed flat. The proper torque for screw (1B) is based on the diameter (B) of the clamp. Refer to the following table for the correct torque.

Table 2
Constant Torque Hose Clamps 
Clamp Type  Diameter (B)  Standard Torque 
Constant Torque Hose Clamp (Belleville Washer) (1)  Up to 50.8 mm (2 inch)  7.5 ± 1 N·m (65 ± 10 lb in) 
Greater than 50.8 mm (2 inch) 11 ± 1 N·m (95 ± 10 lb in) 
Constant Torque Hose Clamp (Tee bolt and Spring) (2)  N/A  7.5 ± 1 N·m (65 ± 10 lb in) 

Wave Liner Clamps

The wave liner worm drive clamp is a clamp with a special liner. this liner has a "v grove" that causes greater pressure points on the hose. This greater compression will offer better sealing capability at the hose connection.



Illustration 3g03869499

Table 3
Width (A) of Clamp  Torque for New Hose 
14 mm (0.6 inch) or greater  7.5 ± 1 N·m (66.4 ± 8.9 lb in) 

Information System:

651E Wheel Tractor-Scraper Transmission Oil Filter and Magnetic Screen - Replace/Clean
3208 Marine Engine Metric (ISO) Fasteners
992G Wheel Loader and 854G Wheel Dozer Power Train Torque Converter (Lockup)
3208 Marine Engine Standard Torque for Worm Drive Band Hose Clamps
D5M Track-Type Tractor Heating and Air Conditioning Controls
3208 Marine Engine Maintenance Log
D6M Track-Type Tractor Heating and Air Conditioning Controls
992G Wheel Loader and 854G Wheel Dozer Power Train Torque Converter
D5M Track-Type Tractor Refill Capacities
D5M Track-Type Tractor Starting with Auxiliary Start Receptacle
D5M Track-Type Tractor Walk-Around Inspection
D5M Track-Type Tractor Transmission Oil Level - Check
651E Wheel Tractor-Scraper Transmission Oil - Change
992G Wheel Loader and 854G Wheel Dozer Power Train Selector and Pressure Control Valve (Transmission)
651E Wheel Tractor-Scraper Walk-Around Inspection
992G Wheel Loader and 854G Wheel Dozer Braking System Parking Brake Control
992G Wheel Loader and 854G Wheel Dozer Power Train Transmission Planetary
3208 Marine Engine Customer Assistance
992G Wheel Loader and 854G Wheel Dozer Braking System Piston Pump (Brake)
992G Wheel Loader and 854G Wheel Dozer Braking System Service Brakes
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Braking System Vane Pump (Implement, Pilot and Braking)
992G Wheel Loader and 854G Wheel Dozer Braking System Monitoring System (Brake Functions)
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Braking System Service Brakes
D6R Track-Type Tractor Gauges