Hydraulic Tank (Steering, Brake)
`
854G Wheel Dozer Hydraulic System
[RENR2125]
854G Wheel Dozer Hydraulic System
Piston Motor (Hydraulic Fan)
854G Wheel Dozer Hydraulic System
Gear Pump (Implement)
HYDRAULIC SYSTEM
TANK GP
854G Wheel Dozer Hydraulic System
Hydraulic Tank (Steering, Brake)
854G Wheel Dozer Hydraulic System
Hydraulic Tank (Implement, Hydraulic Fan)
992G Wheel Loader and 854G Wheel Dozer Braking System
Hydraulic Tank (Steering, Brake)
Show/hide table
![]() | |
Illustration 1 | g01047948 |
Rear View |
Show/hide table
![]() | |
Illustration 2 | g01047887 |
Side View |
Show/hide table
![]() | |
Illustration 3 | g01047922 |
View A-A |
Show/hide table
![]() | |
Illustration 4 | g01047924 |
View B-B |
(1) Torque for the two bolts ...
(2) 7B-3039 Spring (for the drain valve)
- Length under test force ...
26.2 mm (1.03 inch) - Test force ...
15.6 ± 1.2 N (3.50 ± 0.28 lb) - Free length after test ...
36.6 mm (1.44 inch) - Outside diameter ...
19.8 mm (0.78 inch) - Test force ...
(3) Torque for the plug ...
(4) Length of 3G-4090 RTV Silicone Sealant ...
Note: To form a complete seal, overlap the ends of the seal.
(5) Torque for the bolts and the nuts ...
Recommended tightening sequence for the bolts and the nuts around the tank
- Tighten two of the bolts and two of the nuts on all four corners first.
- Tighten all of the bolts and all of the nuts around the tank. Check the bolts and nuts on all four corners of the tank for the correct torque.
- At the overlap of the sealant, check the torque for the bolts and the nuts.
- When possible, torque the nut.
(6) Torque for the locknut ...
Information System:
928G Wheel Loader
Secondary Steering
938G Wheel Loader and IT38G Integrated Toolcarrier
Engine Starting with Auxiliary Start Receptacle - If Equipped
D6M Track-Type Tractor
Walk-Around Inspection
992G Wheel Loader Electrohydraulic System
Pressure Sensor (Implement Pilot Oil)
554 Forwarder and 574 Forwarder
Engine Starting with Jump Start Cables
D6M Track-Type Tractor
Fuses - Replace
928G Wheel Loader
Starting Below 0°C (32°F) with Thermal Starting Aid
992G Wheel Loader Electrohydraulic System
Pilot Control Actuator
928G Wheel Loader
Starting Above 0°C (32°F)
928G Wheel Loader
Product Identification Number, Serial Number and EU's CE Plate Locations
928G Wheel Loader
Model View Illustrations
966G and 972G Wheel Loaders
Display Modules (Caterpillar Monitoring System)
928G Wheel Loader
Bulldozing and Dumping
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Specifications
D6M Track-Type Tractor
Engine Oil Level - Check
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Fuses - Replace
D6M Track-Type Tractor
Transmission Oil Level - Check
928G Wheel Loader
Shipping the Machine
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Circuit Breakers - Reset
928G Wheel Loader
Lifting and Tying Down the Machine
928G Wheel Loader
Towing the Machine
651E Wheel Tractor-Scraper
Directional Turn Signal and Hazard Flasher Control
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Transmission Oil Filter - Replace
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Hydraulic System Oil Filter - Replace